53631
7
Zoom out
Zoom in
Previous page
1/100
Next page
7
ENGLISH
For estimates of the time it takes to charge a battery, refer to
the following table:
The times shown in the table above are approximate and are
based on a 50% discharged battery. The battery charging
times will vary depending on the size, age and condition of
the battery.
Alternator check (fig. B)
A faulty alternator can be the hidden cause of a discharged
battery.
Warning! Check only 12 Vdc systems.
Part 1 (no load)
X Make sure that there is no load on the alternator by
turning off all the vehicles accessories.
X The battery must be fully charged before testing the
alternator.
X Run the engine for 3 minutes to achieve normal idle
speed and verify that there is a no-load voltage.
X Using the function control knob (3), select alternator
check (fig. C) before connecting the clamps to the
battery, ANALYSING ALTERNATOR will be displayed
after the clamps are connected.
X When the unit has completed checking, ALTERNATOR
GOOD will be displayed and the green LED will light to
indicate that the alternator is good or ALTERNATOR
BAD or ENGINE NOT RUNNING and the red LED will
light to indicate that the alternator is out of typical
voltage range.
Part 2 (under load)
X Load the alternator by turning on as many accessories
as possible except for air-conditioning and defrost.
X Once the unit has completed checking, ALTERNATOR
GOOD will be displayed and the green LED will light to
indicate that the alternator is good or ALTERNATOR
BAD or ENGINE NOT RUNNING and the red LED will
light to indicate that the alternator is out of typical
voltage range.
If the first alternator check indicates a good alternator and
the second indicates the alternator is not good, the problem
could be caused by any of the following:
X Loose fan belts.
X An intermittent diode failure.
X Bad connections between the battery and alternator
and/or ground.
Note: ALTERNATOR BAD or ENGINE NOT RUNNING may
be displayed if a number of extra accessory loads have been
added to the charging system, thereby increasing current
demand from the alternator. Make sure that the alternator is
rated to support the application.
Troubleshooting
Display indications, common problems and possible
solutions:
No Functions
X Make sure that the battery charger is plugged into a live
230 Vac outlet.
X Follow the steps outlined in the “Connecting the battery
charger” at the front of this manual.
X The unit will turn on automatically after being properly
connected to the battery. If it does not come on, either it
is not connected properly to the terminals or the voltage
of the battery to be serviced is too low (below 3.0 Volts).
Smart charge fault condition messages
CHECK BATTERY CONNECTIONS - When this message
appears, the most common cause is a poor connection to
the battery.
X Observing the “Safety instructions” at the front of this
manual, disconnect mains cord and the battery
clamps (4), clean the battery terminals and reconnect. If
the situation persists, we recommend taking your
battery to a certified automotive service centre for
evaluation.
REPLACE OR SERVICE BATTERY - The battery being
charged either has an internal open circuit, a shorted cell or
is highly sulphated and cannot accept a normal charge
current. We recommend taking your battery to a certified
automotive service centre for evaluation.
COOL DOWN CYCLE - red LED lit -The ventilation grill that
allows the air from flowing in and out of the charger may be
blocked.
X Make sure there is ample ventilation before resuming
operation.
REVERSE CLAMPS ON TERMINALS - The red LED lights
and a continuous warning tone sounds.
The connections to the battery’s positive and negative
terminals are incorrect.
X Observing the “Safety instructions” at the front of this
manual, disconnect the mains cord and the battery
clamps (4) and reconnect the clamps as described in
the section “Charging the battery”.
OVERTIME CONDITION - When this message is displayed,
the charging cycle has exceeded 18 hours; this condition
may occur because of the following:
20Ah 60Ah 180Ah 360Ah 450Ah 560Ah
10A 1.06hr
**
3.20hr
**
10.00hr
*
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDSBC10A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDSBC10A in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info