578005

Black Decker BDL230S T1 Manual

5
Zoom out
Zoom in
Previous page
1/60
Next page
5
ENGLISH
Additional safety instructions for pipe and wire detectors
◆ Do not use the tool to detect AC voltage in uninsulated,
exposed or free wires.
◆ Do not use the tool as a substitute for a voltmeter.
◆ Be aware that the tool may not always properly detect all
pipes and wires. The following conditions can cause
inaccurate results:
– Low battery
– Thick walls with thin pipes or wires
– Very thick walls
– Very deep wires or pipes
– Walls covered with metal
– Very humid conditions
– Shielded cables
◆ Before use, always test the tool by detecting a known
pipe or wire.
◆ If in doubt contact a qualified contractor.
Warning! This tool will not detect wires in circuits isolated
from the mains supply, cables operating at direct current (DC)
or wires used for telecommunication or computer systems.
Hidden wires (e.g. wall lights) may not be detected when
switches are in the off position.
Warning! This tool will not detect pipes of any other material
than metal.
Features
1. On/off switch (laser)
2. On/off switch (stud/metal finder)
3. Mode selector key
4. LCD screen
5. LED indicator (wire detector)
6. Wall mount holder
7. Laser apertures
Fig. A
8. Wallpin
9. Keyhole wall mount
Assembly
Fitting the battery (fig. B)
◆ Remove the battery cover (10) from the tool.
◆ Insert the batteries into the tool in the orientation as shown.
◆ Refit the cover and let it click into place.
Wall mounting (fig. A & C)
The tool can be mounted to walls using one of the wall
mounts (8 or 9).
Wall pin
If the tool is mounted to drywall or other soft materials,
the wall pin (8) must be used. The position of the laser line
will line up with the mounting location of the pin.
◆ Remove the protective cap (11) from the pin (12) and store
it on the insert as shown (fig. C).
◆ Hold the wall pin at the required height in front of a
suitable location and press the pin straight into the wall.
◆ Install the tool by hanging the holder (6) on the wall mount.
Warning! The pin of the insert is sharp and should be
handled with care. Replace the protective cap immediately
after removing the insert from the wall.
Keyhole wall mount
For surfaces other than drywall, the keyhole wall mount (9)
can be used with a screw in a predrilled hole. The position of
the laser line will line up with the mounting location of the screw.
◆ Hang the wall mount on a screw mounted at the required
height on a suitable location.
◆ Install the tool by hanging the holder (6) on the wall mount.
Use
Using the laser level function (fig. D & E)
◆ Hang the tool on the wall using the appropriate wall mount.
◆ Push the on/off switch (1) up to switch the tool on.
The auto levelling indicator (13) will light up and swing while
the tool is calibrating.
Note: the laser lines will only be level if the tool is kept within
5° from vertical.
◆ Push the on/off switch (1) down to switch the tool off.
Selecting the operating mode (fig. D)
The operating mode is indicated on the display (4).
◆ For the detection of studs, press the mode selector key (3)
as necessary until the ‘STUD’ position (15) is selected.
◆ For the detection of metal studs, pipes, etc., press the
mode selector key (3) as necessary until the ‘METAL’
position (16) is selected.
Using the stud finder function (fig. D & F)
You can use this function to find wooden and metal studs
through drywall boards up to 19 mm thick.
◆ Set the required operating mode.
◆ Place the tool flat against the wall as shown.
◆ Keep the on/off switch (2) depressed.
The scanner bars (17) will light up and the buzzer will sound
once while the tool is calibrating. After calibration is
completed (18):
◆ Slowly slide the tool in a horizontal direction. Make sure
not to tilt or lift the tool.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDL230S T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDL230S T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker BDL230S T1

Black Decker BDL230S T1 User Manual - Polish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info