578004
5
Zoom out
Zoom in
Previous page
1/56
Next page
5
ENGLISH
Never look into the laser beam directly and intentionally.
Do not use optical tools to view the laser beam.
Do not set up the tool at a position where the laser beam
can cross any person at head height.
Do not let children come near the laser.
If the laser line brightness suddenly increases or the
projected line becomes distorted this may indicate a
broken lens. To prevent a laser hazard the tool must not
be used.
Use non-rechargeable batteries only. Do not connect the
laser to any other type of power source.
Features
1. On/off switch
2. Laser head lock switch
3. Laser apertures
4. Laser head
5. Scale
Assembly
Warning! Make sure that the tool is switched off.
Fitting the batteries (fig. A)
Remove the battery cover (6) from the tool.
Insert the batteries into the tool in the orientation as
shown.
Refit the cover and let it click into place.
Installing the tool
The tool can be installed on a surface such as a floor or a wall.
To optimise the length of the laser line, the tool must be
installed onto its bracket. Alternatively, the tool can be
mounted to a wall.
Fitting the tool to the mounting bracket
Install the tool by fitting the slots in the back of the tool
over the hooks of the mounting bracket.
To remove the tool from the bracket, slide the tool off.
Wall mounting (fig. D & E)
The tool can be mounted to walls using the mounting bracket
with a screw (I), a wall pin (II), or an adhesive strip (III).
Keyhole wall mount
The keyhole wall mount (7) is used for mounting to most wall
constructions.
Drive a screw into the wall.
Hang the wall mount onto the fastener by the keyhole (7).
Fit the tool to the bracket.
Wall pin
If the tool is mounted to drywall or other soft materials, the
wall pin must be used:
Remove the protective cap from the pin and store it on the
bracket.
Hold the wall pin at the required height in front of a
suitable location and press the pin straight into the wall.
Hang the mounting bracket onto the fastener by the
keyhole (7).
Fit the tool to the mounting bracket.
Warning! The pin of the bracket is sharp and should be
handled with care. Replace the protective cap immediately
after removing the bracket from the wall
Warning! Do not use a hammer to drive the pin into the wall.
Adhesive strip
If the unit is mounted to surfaces where screws or nails
cannot be used, a removable adhesive adhesive strip (7) must
be used. Adhesive strips can be obtained from your local
retailer.
Warning! Test the strip on an inconspicuous area to make
sure it does not damage the surface material.
Peel the protective foil from one side of the strip (8).
Stick the strip to the bracket.
Peel the protective foil from the other side of the strip.
Press the bracket with the strip to the wall.
Fit the tool to the bracket.
To remove the strip, proceed as follows:
Remove the tool from the bracket.
Hold the bracket with one hand and grasp the end of the
adhesive strip with the other hand.
Slowly stretch the strip parallel to the wall and away from
the bracket, until the entire strip has released.
Dispose of the strip.
Use
Install the tool as required.
Switch the tool on.
Adjust the position of the tool as necessary to position
the laser lines. Be aware that extreme temperature
changes may affect the adjustment of the unit.
After finishing work, always switch off the tool.
Rotating the laser head (fig. B & C)
The laser head (4) can be rotated to allow projection of the
laser lines in both directions.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDL180 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDL180 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker BDL180 T1

Black Decker BDL180 T1 User Manual - Polish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info