709548

Black Decker BCF611C Manual

5
Zoom out
Zoom in
Previous page
1/60
Next page
5
ENGLISH
(Original instructions)
Chargers
u
Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u
Never attempt to charge non-rechargeable batteries.
u
Have defective cords replaced immediately.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
Do not attempt to charge damaged batteries.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
u
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
Features
This tool includes some or all of the following features:
1. On/off switch
2. Forward/reverse slider
3. Bit holder
4. LED work light
5. Charging port
6. Charger
7. USB connector
8. Bit storage
9. Case
10. Case insert
Chargingthebattery(fig.A,B)
u
Insert the USB connector (7) into the charging port (5).
u
Plug in the charger (6).
u
Leave the tool connected to the charger for 1 hour.
u
The charging indicator (5a) will illuminate during charging.
u
The tool can also be charged while it is in the case (9), as
illustrated in figure B.
Fitting and removing a screwdriver bit (fig.C)
This tool uses screwdriver bits a 6.35 mm hexagonal shank.
u
To t a bit, insert the bit shaft (8) into the bit holder (3).
u
To remove a bit, pull the bit shaft (8) out of the bit holder
(3).
LEDworklight(g.D)
The LED work light (4) is activated automatically when the on/
off switch (1) is depressed. The LED will also illuminate when
the trigger is depressed and the forward/reverse slider (2) is in
the locked off position (central position).
Selectingthedirectionofrotation(fig.E)
For tightening screws, use forward rotation. For loosening
screws use reverse rotation.
u
To select forward rotation, push the forward/reverse slider
(2) to the forward position.
u
To select reverse rotation, push the forward/reverse slider
(2) to the rearward position.
u
To lock the tool, set the forward/reverse slider into the
centre position.
Screwdriving
u
Select forward or reverse rotation using the forward/
reverse slider (2).
u
To switch the tool on, press the on/off switch (1).
u
To switch the tool off, release the on/off switch (1).
Hints for optimum use
Screwdriving
u
Always use the correct type and size of screwdriver bit.
u
If screws are difcult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u
Always hold the tool and screwdriver bit in a straight line
with the screw.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any cleaning or maintenance on
the tool, unplug the charger.
u
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BCF611C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BCF611C in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info