3354
4
Zoom out
Zoom in
Previous page
1/56
Next page
4
ENGLISH
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for sanders
Always wear a dust mask whenever sanding.
Thoroughly remove all dust after sanding.
Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal
which may produce toxic dust:
- Wear a dust mask specifically designed for protection
against lead paint dust and fumes and ensure that
persons within or entering the work area are also
protected.
- Do not let children or pregnant women enter the work
area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Features
1. On/off switch
2. Dust extraction outlet
3. Sanding base
4. Paper clamp lever
5. Variable speed control knob (KA196E)
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (fig. A & B)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting regular sanding sheets (fig. A)
Make sure that the tool is switched off and unplugged.
Soften the sanding sheet by rubbing its non-abrasive side
over the edge of a worktop.
Press the paper clamp levers (4) upwards to release them
from the retaining grooves and open the paper clamps by
pressing them down.
Place the sheet onto the sanding base, making sure that
the holes in the sheet line up with the holes in the base.
Insert the edge of the sanding sheet into the front paper
clamp as shown.
Press the front paper clamp lever (4) downwards and
locate it in the retaining groove.
While keeping a slight tension on the sheet, insert the
rear edge of the sheet into the rear paper clamp.
Press the rear paper clamp lever (4) downwards and
locate it in the retaining groove.
KA196/KA196E - Fitting sanding sheets with nylon loops
(fig. B)
Make sure that the tool is switched off and unplugged.
Press the sheet firmly and evenly onto the sanding base
(3), making sure that the holes in the sheet line up with
the holes in the base.
Connecting a vacuum cleaner (fig. C)
Insert the adaptor (6) into the dust extraction outlet (2).
Connect the hose (7) of the vacuum cleaner to the
adaptor.
Use
Warning! Let the tool work at its own pace. Do not overload.
KA196E - Variable speed control
The variable speed control allows you to adapt the speed of
the tool to the workpiece material.
Set the control knob (5) to the desired setting. Use a high
speed for wood, medium speed for veneer and synthetics
and low speed for acrylic glass, non-ferrous metals and
for removing paints.
Switching on and off
CD380/CD400/AST4XC
To switch the tool on, slide the on/off switch (1) forward
(position I).
To switch the tool off, slide the on/off switch to the rear
(position 0).
AST4XC_EURA5.P7 16-08-2005, 20:254
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker AST4XC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker AST4XC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info