53556

Black Decker AST18XC Manual

4
Zoom out
Zoom in
Previous page
1/96
Next page
4
ENGLISH
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
• For drilling in masonry, set the drilling mode selector
(4) to the position.
• For drilling in other materials and for screwdriving,
set the drilling mode selector (4) to the
position.
Switching on and off (fig. E)
• To switch the tool on, press the variable speed switch
(1). The tool speed depends on how far you press
the switch. As a general rule, use low speeds for
large diameter drill bits and high speeds for smaller
diameter drill bits.
• For continuous operation, press the lock-on button
(2) and release the variable speed switch. This
option is available only at full speed.
• To switch the tool off, release the variable speed
switch. To switch the tool off when in continuous
operation, press the variable speed switch once
more and release it.
Accessories
The performance of your tool depends on the accessory
used. Black & Decker and Piranha accessories are
engineered to high quality standards and designed to
enhance the performance of your tool.
By using these accessories you will get the very best
from your tool.
Maintenance
Your tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care
and regular cleaning.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the
new plug.
• Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth
terminal. Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 5 A.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Make this product
available for separate collection.
Additional safety instructions for hammer drills
• Wear ear protectors. Exposure to noise can cause
hearing loss.
• Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
• Preferably wear a dust mask.
Electrical safety
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on
the rating plate.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch
4. Drilling mode selector
5. Side handle
6. Chuck
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle (fig. A)
• Turn the grip (7) counterclockwise until you can
slide the side handle (5) onto the front of the tool as
shown.
• Rotate the side handle into the desired position.
• Tighten the side handle by turning the grip
clockwise.
Fitting a drill bit or screwdriver bit (fig. B)
• Open the chuck by turning the front part (8) with one
hand while holding the rear part (9) with the other.
• Insert the bit shaft (10) into the chuck and firmly
tighten the chuck.
Removing and refitting the chuck (fig. C)
• Open the chuck as far as possible.
• Remove the chuck retaining screw (11), located in
the front part of the chuck, by turning it clockwise
using a screwdriver.
• Tighten an Allen key (12) into the chuck and strike
it with a hammer as shown.
• Remove the Allen key.
• Remove the chuck by turning it counterclockwise.
• To refit the chuck, screw it onto the spindle and
secure it with the chuck retaining screw.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (fig. D)
• For drilling and for tightening screws, place the
forward/ reverse switch (3) in the neutral position.
• For loosening screws or removing a jammed drill bit,
turn the forward/reverse switch (3) to the left.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker AST18XC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker AST18XC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info