53554
5
Zoom out
Zoom in
Previous page
1/64
Next page
5
ENGLISH
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for angle grinders
Read the instruction manual before use.
Wear safety glasses or goggles when operating this
tool.
Wear ear protection when operating this tool.
Always use eye and ear protection when operating this
tool.
Personal protective equipment such as dust mask, gloves,
helmet and apron should be worn.
Do not cut or grind light metal with a magnesium content
exceeding 80%, since this type of metal is flammable.
Only use grinding and cutting discs and other accessories
recommended in this manual.
Make sure that the maximum speed of the grinding or
cutting disc exceeds the no-load speed of the tool.
Do not use grinding and cutting discs that do not conform
to the dimensions stated in the technical data. Do not use
separate reducing bushings or adapters or make
unauthorised modifications to adapt large hole abrasive
wheels.
Do not cut workpieces requiring a maximum depth of cut
exceeding that of the cutting disc.
Do not use cutting discs for side grinding.
Inspect grinding and cutting discs before each use. Do not
use chipped, cracked or otherwise defective discs.
Ensure that the abrasive product is correctly mounted and
tightened before use and run the tool at no-load for 30 s
in a safe position, stop immediately if there is considerable
vibration or if other defects are detected. If this condition
occurs, check the machine to determine the cause.
Ensure that blotters are used when they are provided with
the bonded abrasive product and when they are required.
When applying a threaded hole disc, ensure that the
thread is long enough to accept the spindle length.
Never use the tool without the guard.
Check that the workpiece is properly supported.
Do not exert side pressure on the grinding or cutting disc.
Ensure that sparks resulting from use do not create a hazard
e.g. do not hit persons, or ignite flammable substances.
Beware that after switching off the tool the wheel
continues to rotate for a short period.
Ensure that ventilation slots are kept clear when working
in dusty conditions. If it should become necessary to clear
dust, first disconnect the tool from the mains supply.
Avoid damaging internal parts, use a soft brush or dry
cloth, do not use metallic objects.
Abrasive wheels shall be stored and handled with care in
accordance with manufacturer’s instructions and always
store grinding and cutting discs in a dry place.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Side handle
3. Spindle lock
4. Guard
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing the guard (fig. A & B)
Fitting
Place the tool on a table, with the spindle (5) facing up.
Place the spring washer (6) over the spindle and locate it
on the shoulder (7).
Place the guard (4) onto the tool as shown.
Place the flange (8) over the spindle with the protruding
pips towards the guard. Make sure that the holes in the
flange align with the screw holes.
Secure the flange with the screws (9). Make sure that the
screws are fully tight and that the guard can be rotated.
Removing
Use a screwdriver to remove the screws (9).
Remove the flange (8), guard (4) and spring washer (7).
Store these parts carefully.
Warning! Never use the tool without the guard.
Fitting the side handle
Screw the side handle (2) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs (fig. C - E)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data).
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker AST15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker AST15 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker AST15

Black Decker AST15 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info