581276

Black Decker ASI200 T1 Manual

5
Zoom out
Zoom in
Previous page
1/68
Next page
5
ENGLISH
X When the item to be inflated has reached the preset
value the unit will automatically turn off.
X To turn the inflator off press switch (5) to the 0 position.
X Remove the valve adaptor or accessory from the
inflated item and the 12 Volt adapter (6) from your
vehicle's 12 Volt accessory socket.
Note: If the 12 Volt adapter is removed from the vehicles
12 Volt accessory socket, all settings will be lost and will
need to be re-entered following the instructions under the
heading 'Setting the required pressure'.
Operating the area light
X To operate the area light (1), make sure that the 12 Volt
adaptor (6) is plugged into the vehicle's 12 Volt
accessory socket.
Note: Make sure that your 12 Volt accessory socket is live.
On some vehicles the accessory socket may only become
live when the ignition key is in the accessory position.
X To turn the area light on, press the area light on/off
switch (7) located on the side of the unit to the I position.
X To turn the area light off, press the area light on/off
switch (7) located on the side of the unit to the 0
position.
To replace the bulb (fig. E)
Warning! Make sure that the 12 Volt adaptor is not
connected before starting this procedure.
X Remove the screw (10) from the top of the lens
cover (12).
X Pull the lens cover (12) down using the tab (11) to get
access to the bulb (13).
X To remove the bulb, push in and turn clockwise (fig. E).
X Replace the bulb (13) with a one of the same type and
wattage (12V/5W).
X Fit the lens cover (12) and secure with the screw (10).
Using your inflator as a pressure gauge
X Make sure that the unit is powered as described in the
section 'Operating the Inflator'.
X Connect the universal valve adaptor and accessories if
required to the item to be inflated making sure that the
lever of the valve adaptor is in the down position to lock
it in place.
X The display will now show the actual pressure value in
the item.
Maintenance
Your Black & Decker corded/cordless appliance/tool has
been designed to operate over a long period of time with
a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular
cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
X Switch off and unplug the appliance/tool.
X Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
X Or run the battery down completely if it is integral and
then switch off.
X Unplug the charger before cleaning it. Your charger
does not require any maintenance apart from regular
cleaning.
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust from
the interior (when fitted).
Troubleshooting
Replacing the fuse in the vehicle dc accessory plug
X Remove the cap by turning it counter-clockwise.
X Loosen the cap and centre pin.
X Remove the fuse.
X Fit a new fuse of the same type and size (8A/250V).
X Refit the cap and centre pin.
X Tighten the cap by turning clockwise onto the plug.
Problem Possible cause Possible solution
Inflator will not
operate
12 Volt adaptor
not connected
Connect the 12 Volt
adaptor
Accessory socket
not live
Turn key to accessory
position
No preset
valve set
Set preset value
The fuse in the
12 Volt adaptor
is blown
Replace the fuse with
one of the same size
and type (8A/250V)
Cord or switch is
damaged.
Have the cord or
switch replaced at a
Black & Decker Service
Centre or Authorized
Service Centre.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ASI200 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ASI200 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker ASI200 T1

Black Decker ASI200 T1 User Manual - Turkish - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info