621998

Bissell Powerwash Lift-Off 1190 Manual

10
Zoom out
Zoom in
Previous page
1/12
Next page
10
D
Care,
Maintenance & Storage
Machine care (check regularly)
D-1 Cleaning suction gate
The suction gate automatically diverts air
when the portable deep cleaner is detached.
This should be checked and cleaned
regularly for any dirt and debris.
1. Step on pedal and remove portable spot
cleaner. Remove dirty tank.
2. Remove two screws and pull off suction
gate door.
3. Wipe suction gate clean and rinse suction
gate door under water.
4. Replace suction gate door and two
screws.
D-2 Cleaning spray tips
1. Step on pedal and remove portable spot
cleaner.
2. To remove black spray tip, unlatch tab
on front portion of spray tip from base of
machine and pull up and out of red receiver.
3. Clean by rinsing under water.
4. Replace black spray tip by inserting back
into red receiver and latching tab back down
into base of machine.
5. Repeat steps on second spray tip.
D-3 Small belt removal and
replacement (as needed)
Occasional replacement of one or both belts
may become necessary. If needed, please
follow instructions below.
1. Turn off machine and unplug from
outlet. Remove portable spot cleaner.
2. Remove nozzle assembly from machine.
Refer to step 2 in section C-5.
3. Turn machine on its side.
IMPORTANT: With portable spot cleaning
pedal facing down:
4. Remove end cap by unscrewing 3 screws.
Take care not to drop screws into machine.
5. Remove 1 silver screw from pivot arm.
6. Remove pivot arm by gently lifting up.
7. Remove small brush belt.
8. Replace small brush belt and reverse
steps above.
9. Manually rotate brushes by hand to make
sure they move freely. There may be a slight
resistance from motor.
D-4 Brush removal and large
belt replacement (as needed)
Brushes can be removed for cleaning or
replacement as needed.
1. Follow small belt removal instructions
steps 1-7 in section D-3.
2. Remove brush rolls by pulling off of metal
rods. Be careful not to lose small washer at
each end of brush rolls.
3. Re-attach large belt to grooves on end
of new or cleaned brush rolls. If belt is
damaged, replace with new belt.
4. Place cleaned or new brush rolls back
onto rods. Make sure one washer is on each
end of rollers prior to sliding onto rod. Be
sure brush is seated completely on rod.
5. Replace small belt over grooves in back
roller and metal cog.
6. Replace pivot arm and secure with
silver screw.
7. Re-attach end cap by tightening with
(3) black screws.
8. Replace nozzle assembly back onto
machine. Refer to step 2 in section C-5.
For questions or assistance installing or
replacing belt(s) or brushes, please call
BISSELL Consumer Care.
To reduce the risk of electric shock, turn power
switch off and disconnect plug from electri-
cal outlet before performing maintenance or
troubleshooting checks.
www.BISSELL.com
… 10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bissell Powerwash Lift-Off 1190 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bissell Powerwash Lift-Off 1190 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bissell Powerwash Lift-Off 1190

Bissell Powerwash Lift-Off 1190 User Manual - German - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info