669273
9
Zoom out
Zoom in
Previous page
1/100
Next page
C-4 Upholstery Cleaning
1. Important! If using to wet clean upholstery,
check the upholstery tags before hand.
a. Check manufacturer’s tag before
cleaning. “W” or “WS” on the tag means
you can use your cleaner. If the tag
is coded with an “X” or an “S” (with a
diagonal stripe through it), or says “Dry
Clean Only”, do not proceed with wet
cleaning. Do not use on velvet or silk.
If manufacturer’s tag is missing or not
coded, check with the furniture maker
or the furniture dealer.
b. Check for colourfastness in an
inconspicuous place.
c. If possible, check upholstery stuffing.
Coloured stuffing may bleed through
fabric when wet.
d. Plan activities to allow upholstery time
to dry.
e. Vacuum thoroughly.
2. Refer to the “Getting Ready to Wet Clean”,
section C-2.
3. Attach desired wet cleaning tool
directly to grip.
4. Place tool directly on surface. Press Spray
Trigger to spray cleaning solution while
pulling tool towards you.
5. Keep nozzle of tool firmly against surface
and continue to make slow forward and
backward wet passes until no more dirt can
be removed. Caution: Do not overwet.
6. Release Spray Trigger and make slow
forward and backward passes over same area
to remove any residual water.
7. Continue to clean entire surface.
8. If machine loses suction, stop wet
cleaning and check Collection Tank level.
Empty if full.
9. If machine stops spraying, turn OFF
Wet Clean Button immediately and check
Solution Tank level. Refill if empty.
10. Refer to section D for machine
care instructions.
C-5 Hard Floor Cleaning
1. Open Quick Release™ Hose Door, turn
cleaning mode selector to “WET CLEAN”,
then close hose door.
2. Remove tool caddy from back of
cleaner if in place.
3. Unscrew measuring cap from Solution Tank.
Fill Solution Tank with warm tap water to fill
line. Add one full measuring cap of BISSELL
hard floor cleaning formula then screw cap
tightly back onto Solution Tank.
IMPORTANT: Be sure to use BISSELL® hard
floor cleaning formula when cleaning sealed
hard floor surfaces.
4. Place Solution Tank back in the cleaner.
5. Attach Microfibre mop pad to quick dry
hard floor tool by attaching ends to Velcro
strips on top of tool.
NOTE: Be sure top of mop pad is positioned
below brushes on hard floor tool.
6. Attach Quick Dry Hard Floor Tool to end
of the wand.
7. Plug into a proper electrical socket and
push Power and Wet Clean Buttons ON.
8. Place tool directly on the hard floor
surface, resting on the pad.
9. Press Spray Trigger to moisten mop pad
with cleaning solution.
Caution: Do not oversaturate.
10. Move tool back and forth across floor;
using solution, brushes and mop pad to clean.
Press Spray Trigger as needed.
11. With Spray Trigger released, swivel tool
forward and pull back across cleaned floor to
remove any residual water. This will create the
best suction and will help get the hard floor
surface as dry as possible.
12. Continue to clean entire floor.
13. If cleaner loses suction, stop wet cleaning
and check Collection Tank level. Empty if full.
14. If cleaner stops spraying, turn OFF Wet
Clean Button immediately and check
Solution Tank level. Refill if empty.
15. When finished, be sure to remove
Microfibre mop pad and clean by hand
or machine wash as needed. Allow to
dry completely before next use.
16. Refer to section D for machine
care instructions.
EN
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bissell Hydro Clean Pro Heat Complete 1474J at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bissell Hydro Clean Pro Heat Complete 1474J in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 6,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bissell Hydro Clean Pro Heat Complete 1474J

Bissell Hydro Clean Pro Heat Complete 1474J User Manual - English - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info