661286

Bioland 2006 Manual

8
Zoom out
Zoom in
Previous page
1/10
Next page
M1
M2
3. Press “M1/M2” button to select
the user of memory location within
3 seconds while it is flashing.
4. Device will automatic start measurement within a few seconds, the cuff in the
arm will automatically inflate. When the value on LCD increases to around
150-200 (mmHg), and start to release the air, and decrease pressure in the
cuff automatically when it senses the heart beat, the mark ( ) will flash on
LCD.
5. After measurement the screen will display systolic value, diastolic value,
pulse rate per minute and pressure classification according to World Health
Organization (WHO) reference table, then automatically store the measured
records into user's memory.
Level indicator-
One bar for Systolic below 99 mmHg (LED Green color)
Two bars for Systolic between 100 ~ 139 mmHg (LED Green color)
Three Bars for Systolic between 140 ~ 159 mmHg (LED Yellow color)
Four bars for Systolic above 160 mmHg (LED Red color)
Irregular Heartbeat Detection(IHD)
During measurement, if the sensor detects more than twice of
Heartbeat out of 25% tolerance to your average Heart rate, the
display will turn on Irregular Heartbeat icon .
6. Press " " button again to turn off the unit.
* Even if you forget to press "POWER" button, the unit will turn off
automatically in approximately 2.5 minutes.
Note:
* The value measured will be too low if you hold your cuff higher than heart
level, or will be too high if you hold your cuff lower than heart level.
* The unit may store 50 measurements per user, If one user more than 50
records, it will delete the earliest data. (Total 100 memories for 2 users)
* During measurement do not speak or shake as which may affect the accuracy
of the result.
* If you want to stop the measurement during measurement process, just press
the " " button to stop immediately.
RECALLING MEMORY
1. Press "M1/M2" button, display with “U1” or “U2” flashing, press “memo” button
again while it is flashing to select user U1 or U2 , you are going to review.
2. Device display last 3 measurement data average within few seconds and total
number of memory inside that user.
3. Press " " button to review the memory. Repeated press " " button to
review memory data in ascending order.
4. Press " " button to review the memory. Repeated Press " " button to
review memory data in descending order.
Note: To delete all memory in both users U1 and U2, please refer to the Page 10
point 5 for details.
-13- -14-
M1
M2
Average last 3
measurements
Total measurements
in user's memory
User
1. Use a dry soft cloth to clean the unit. If
necessary, use a cloth lightly dampened
with tap water.
HOW TO MAINTAIN AND STORE THE UNIT
SYS.
DIA.
SET
M1
M2
B
l
o
o
d
P
r
e
s
s
u
r
e
M
o
n
i
t
o
r
… 8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bioland 2006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bioland 2006 in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info