470375

Beurer EM 40 Manual

25
Zoom out
Zoom in
Previous page
1/28
Next page
25
7. Application
7.1 Advice on application
•
If the machine is not used within 3 minutes, it switches off automatically
(automatic switch-off function). When it is switched on again, the LCD
main menu screen appears, with the last used submenu flashing.
•
If an admissible key is pressed, there is one short beep. If an inadmissible
key is pressed, there are two short beeps.
7.2 Procedure for TENS, EMS and MASSAGE programmes 01–10
(quick start)
•
From the programme charts, select a programme that is suitable for your
purpose.
•
Place the electrodes in the area selected and connect these to the machine.
The corresponding positioning suggestions may help you here.
•
Press the ON/OFF key in order to switch on the machine.
•
Press MENU and navigate through the sub-menus (TENS/
EMS/MASSAGE) and confirm your selection with ENTER.
(Fig. 1, example of TENS display)
•
Using the UP/DOWN keys, select the programme you want
and confirm with ENTER (Fig. 2, example of display for No. 1
TENS programme).
•
Using the UP/DOWN keys, select the total treatment time
and confirm with ENTER (Fig. 3, example of 30-minute treat-
ment duration).
The machine is in wait status (Fig. 4).
•
Press ON/OFF to start the stimulation treatment. The opera-
tion status display starts to change (Fig. 5).
•
Select the pulse intensity which is the most comfortable for
you by pressing the key CH 1+/CH 2+.
The pulse intensity display adapts accordingly.
7.3 Procedure for TENS/EMS programmes 11 to 20
(individual programmes)
Programmes 11 to 20 are preset programmes which you can also individualise.
Here you can set pulse frequency.
•
From the programme charts, select a programme that is suitable for your
purpose.
•
Place the electrodes in the area selected and connect these to the machine.
The corresponding positioning suggestions may help you here.
•
Press the ON/OFF key in order to switch on the machine.
•
Press MENU and navigate through the sub-menus (TENS/
EMS/MASSAGE) and confirm your selection with ENTER.
(Fig. 1, example of TENS display)
•
Using the UP/DOWN keys, select the programme you want
and confirm with ENTER (Fig. 2, example of display for No.
11 TENS programme).
•
Using the UP/DOWN keys, select the frequency you want
for Cycle 1 (Hz) and confirm with ENTER (Fig. 3). Repeat this
process for all subsequent cycles.
•
To terminate frequency setting, set the frequency (Hz) after
the cycle last required “--0” and press ENTER. All frequency
settings of subsequent cycles are then automatically set at
“0” and thus not taken into account.
i
Tip: Hold down the ENTER key for 2 seconds in order to
skip frequency settings and access ‘treatment time setting’.
In the event that you need all 8 cycles, you can also press
ENTER for 2 seconds to terminate selection of frequency
settings.
•
Using the UP/DOWN keys, select the desired treatment time
and confirm with ENTER (Fig. 4, example of 30-minute treat-
ment duration).
•
The machine is in wait status (Fig. 5).
•
Press ON/OFF to start the stimulation treatment. The opera-
tion status display starts to flash (Fig. 6).
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 1
Fig. 2
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beurer EM 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beurer EM 40 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info