Manual Bestway 65052 Hydro-Force (page 3 of 32) (All languages)

753218

Zoom out

Zoom in

1/32

Oar

Boat

Components:

• Repair Patch

• Deflation Pipe Storage bag

Oar blade x 4

Shaft x 2

Coupling x 4

Removable Fin x 2

Seat x 2

Screw Valve x 3

Footrest Cushion

Hand Pump

Safety rope

NOTE: All drawings for illustration purpose only. May not reflect actual product.

Oars Installation

Safety rope installation

Insert the rope into the holes of the D-buckles orderly, and then tighten the ends of the rope to the D-buckles.

Caution: 1. Safety ropes shall be fitted to both sides of the bow and stern areas only and shall not impede the normal

operation of the craft.

2. Do check carefully if the saving rope is tightened well.

Seats and Storage bag assembly

After the craft is inflated, connect the belts of the seat’s to the side buckles on the craft, make the storage bag is vertical.

The location of the seats can be adjustable along with center of the craft floor.

Connect the storage bag to the D-buckle.

Repair

1. If there is a leak, take out the liner, spray water onto the chamber surface and look for air bubbles. Soapy water works

well.

2. If there is a small puncture, repair it according to the instruction on repair patch.

3. If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or send the boat to a

speciality shop to make the repair.

Storage

1. Remove the Oars from the Velcro oar band; take down the storage bag and seats.

Note: Keep all accessories for future use.

2. Carefully clean the craft using a mild soap with clean water.

Note: Do not use acetone, acid, and/or alkaline solutions.

3. Use a cloth to gently dry all surfaces. Do not dry the product in direct sunlight.

Note: Also, never dry with equipment such as electric blowers. Doing so will cause damage and shorten the craft’s

life span.

4. Deflate the hull chambers. Deflate all the hull chambers at the same time so the air-pressure drops together. This will

prevent damage from occurring to the boat inner structures. Next deflate the floor.

5. Fold the craft from front to back to remove additional air. You can also use a pump to drain any remaining air.

6. Store in a cool, dry place and out of children’s reach.

Registration ( For US/Canada customers only )

If you need to register your boat, please have the boat Hull Identification Number and model name ready and then visit

www.bestwaycorp.com/support to obtain your Certificate of Origin, or you can send e-mail to service@bestwaycorp.us

for the Certificate of Origin.

PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER WHEN YOU

SELL THE CRAFT.

WARNING

IMPORTANT SAFETY INSTRUCTIONS

Follow all the Safety and Operating Instructions. If you don’t follow these instructions, it may cause the boat to overturn

or explode and result in drowning.

1. Do not exceed the maximum recommended number of persons. Regardless of the number of persons on board, the

total weight of persons and equipment must never exceed the maximum recommended load. Always use the seats/

seating spaces provided.

2. When loading the craft, never exceed the maximum recommended load: Always load the craft carefully and

distribute loads appropriately to maintain design trim (approximately level). Avoid placing heavy weights high up.

NOTE: The maximum recommended load includes the weight of all persons onboard, all provisions and personal

effects, any equipment not included in the light craft mass, cargo (if any) and all consumable liquids (water, fuel,

etc.).

3. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected and used at all

times.

4. Before every use, carefully inspect all boat components including air-chambers, grab ropes, oars, and air valves, to

ensure everything is in good condition and tightly secured. If you find any damage, please stop to repair it.

5. Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat takes on water.

6. When the boat is in motion, all passengers must remain seated at all times to avoid falling overboard. Keep the boat

balanced. Uneven distribution of persons or load in the boat may cause the boat to overturn and result in drowning.

7. Use the craft in sheltered water, up to 300m (984 feet). Be careful with natural factors such as wind, tide waters and

tidal waves. BE AWARE OF OFFSHORE WINDS AND CURRENTS. Always wear a lifejacket!

8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the other air chamber

to prevent the boat from sinking.

9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells, glass, etc. may

puncture the boat. To avoid damage, do not drag the boat on rough surfaces.

10. The boat is intended for beach use, short-time and short-distance cruising.

11.

Be aware of the potential harmful effects of liquids such as battery acid, oil or petrol. The liquids may damage your boat.

12. Inflate according to the numbered air chamber and rated pressure of the boat, or it will cause over-inflation potential

and boat explosion. Exceeding the data given on the capacity plate may cause the craft to be damaged, overturn

and lead to drowning.

13. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.

14. Know how to operate a boat. Check in your local area for information and/or training as needed. Inform yourself

about local regulations and dangers related to boating and/or other water activities.

SAVE THESE INSTRUCTIONS

Installation

1. Spread out the kayak on level ground.

2. Assemble the removable fin to the bottom of the kayak. Make sure the curvature of the fin is pointed towards the

back end of the kayak.

NOTE: Assemble the fin before inflation and also disassemble it after deflation.

NOTE: To avoid damage to the removable fin, do not enter shallow water.

• Inflate the air chambers with a HAND air pump.

Caution: Under and over-inflation of the boat will result in safety hazards. It is better to check the pressure of the boat

each time before using.

NOTE: Pressure gauge is for inflation purpose only, and the value of the pressure gauge is just for reference, should

not be used as a precision instrument.

• Never stand on or rest objects on the boat during inflation.

• Inflate to the nominal pressure (0.8 psi)

VENTURA X2 KAYAK SAVE THESE INSTRUCTIONS

Inflation

NEVER USE HIGH PRESSURE AIR TO INFLATE INFLATABLES. THIS CAN DAMAGE YOUR PRODUCT AND VOID

YOUR WARRANTY

1 2 3 4 5 6 7

D-buckle Buckle Velcro oar band Handle Storage bag Seat Safety rope

Technical Specifications

Item

65052

Inflated Size Recommended

working pressure

0.06 bar (0.8 psi)

Maximum

load capacity

200 kg (440 Ibs.)

Maximum number

of persons

2 adults

3.30m x 86cm

10’10” x 34”

Construction of the boat

NOTE: All drawings for illustration purpose only.

May not reflect actual product. Not to scale.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bestway 65052 Hydro-Force in the language / languages: All languages as an attachment in your email.

The manual is 18,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bestway 65052 Hydro-Force Manual

Product: