768220
3
Zoom out
Zoom in
Previous page
1/112
Next page
10 11
be used in a vehicle.
When the child seat is mounted in the car check all the areas where
the child seat might touch the interior. We recommend using a (BeSafe)
protection cover in these places to avoid cuts, marks or discolouration to
the interior of the vehicle, especially in vehicles with leather or wooden
interiors.
If in doubt, consult either the car seat manufacturer or the retailer.
Preparing to install
Installation
1. When installing in the back seat of the vehicle, push the front seat of the
vehicle forward as far as possible and adjust the back rest into an upright
position (if it can be adjusted).
2. When installing in the front seat of the vehicle, adjust the back rest into
an upright position.
3. Position the vehicle on a horizontal surface when installing the seat.
4. When the base is lifted the floor support should fall downwards from
underneath the base. Do this outside the car.
5. Push down the switch for the ISOfix connectors at both sides to release
the ISOfix connectors. (2)
6. Position the base on the vehicle seat. Click the ISOfix connectors on to
the ISOfix anchorages on the vehicle seat. Make sure that both ISOfix
indicators are green. (3)
7. Push the seat towards the backrest of the vehicle seat until it touches the
backrest. (4)
8. The ISOfix connectors willhave resistance sliding in, in the most outward
positions, before they are connected with the ISOfix anchorage of the
vehicle.
9. Tip: once the ISOfix connectors are installed, the seat can be turned
towards the door of the vehicle to get a better view on the installation
display.
10. Remove the yellow cap from the floor support. Adjust the floor support, so
it is in contact with the floor of the vehicle. (5)
11. The height indicator of the floor support shows green when the floor
support is in contact with the floor. (5)
12. Lift the base at the front side (near the spirit level) and extend the floor
support till the spirit level is in the middle, indicating a horizontal position
of the base. (5)
13. Tip: place one foot onto the bottom end of the floor support while lifting
the base to make adjusting the length at this step easier.
14. The alarm sound stops when the floor support indicators show green and
it is in contact with the floor and when the horizontal spirit level shows a
horizontal position of the seat. (5)
15. When having the child seat installed rear facing in the back, it is
recommended to position the front vehicle seat in a way that it is close to
the touchpoint with the child seat. Make sure that the child seat can still
rotate freely.
When having the child seat installed rear facing on the passenger seat in
the front, it is recommended to position the passenger seat in a way that
the dashboard is close to the touchpoint with the child seat. Make sure
that the child seat can still rotate freely.
16. Tip: If you feel like the base has too much side movement, you can install
the seat tighter against the vehicle seat backrest. Make the support leg
short, grab the base and push it against the vehicle backrest with more
force. Move it side to side until you hear one more ‘click’ per side, then lift
the base into horizontal position again (see step 10-14).
17. The seat is delivered with removable SIP+ (side impact protection +).
This extra side impact protection should be used on the doorside of the
vehicle. To connect your SIP+ version, follow the instruction drawings
on the SIP+ included with your seat. The seat already oers high level
integrated side impact protection. This extra side impact protection
improves the protection in the side impact still further. (6)
Adjustable headrest
Shoulder straps
Baby insert
Baby cushion
Harness buckle
Central adjuster
Reclining handle
Release handle headrest
Installation screen
Spirit level
Battery compartment
Floor support
Floor support height indicator
Height adjuster floor support
Rotation release handle
Switch for ISOfix connectors (2x)
ISOfix connectors (2x)
ISOfix release switch
ISOfix indicators (2x)
ISOfix car anchorage (2x)
(1a)
(1b)
(1c)
(1d)
(1e)
(1f)
(1g)
(1h)
(1i)
(1j)
(1k)
(1l)
(1m)
(1n)
(1o)
(1p)
(1q)
(1r)
(1s)
(1t)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeSafe iZi Turn B i-Size at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeSafe iZi Turn B i-Size in the language / languages: All languages as an attachment in your email.

The manual is 3,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info