474161
67
Zoom out
Zoom in
Previous page
1/67
Next page
NEDERLANDS
67
SCH2SCH1
ON
12345678
12
ON
X2 2
X1S
1/N~230/240 V
50Hz
P1
M
LD4
5 212012137120777420
LD3
INI
2LK
TEST
12V/10W
LD2LD1
KL1
ST2 ST3ST1
4TS
SCH1
SCH2
21
NO
ON
12345678
20 21 5 23
12
Sokkel G 4
10 Printplaatoverzicht en beknopte programmeerhandleiding
Fabrieksinstelling Fabrieksinstelling
Functie DIP-schakelaar (SCH1) ON OFF
1: Stop toets Nee Ja
2: Lichtbarrière Nee Ja
LED-indicatie Brandt Knippert
LED1 (rood) Motor draait in richting dicht --
LED 2 (groen) Motor draait in richting open --
LED 3 8,2kΩ strip geactiveerd OSE-lijst geactiveerd
LED 4 Stopcircuit onderbroken Lichtbarrière geactiveerd
Beknopte programmeerhandleiding leermodus
1.Zwarte toets indrukken en ingedrukt houden tot de lamp
2x knippert. Daarna toets loslaten.
2.Met witte toets de poort openen (continue opdracht) tot aan
de “poort open” positie.
3.Kort de zwarte toets indrukken.
4.Poort sluit, opent en sluit nog 2x automatisch. Daarna is de
programmering afgesloten.
Beknopteprogrammeerhandleiding gedeeltelijke
opening:
1.Zwarte toets indrukken en ingedrukt houden tot de lamp
2x knippert.
2.Additioneel de witte toets indrukken tot de lamp sneller
knippert, dan beide toetsen loslaten.
3.Met de witte toets de poort openen (continue opdracht)
tot de gewenste “Deel open” positie.
4.Kort de zwarte toets indrukken. De programmering van de
gedeeltelijke openingspositie is afgerond.
Functies DIP-schakelaar (SCH2) ON OFF
1: Lichtbarrièreanalyse 2-draads contact
2: Analyse sluitrandbeveiliging OSE 8,2kΩ
3: Snel-open ja nee
4: Soft-loop snelheid bij poort dicht 30% 50%
5: Kort achteruit bij poort dicht lang kort
6: Optionele relais lichtfunctie
7: Gedefinieerde richtingsbevelen ja nee
8: Poort dicht indicatie ja nee
waar-
schuwingslicht
Programmering van de aandrijvingverlichting
bij gesloten poort, duur 150 sec.
1. Trek de stekker uit het stopcontact.
2. Druk de zwarte toets in (continu contact)
3. Steek bij ingedrukte leertoets de stekker weer in het stopcontact.
4. Na inschakeling van de aandrijvingsverlichting de leertoets loslaten.
Bij herhaling van deze procedure wordt de fabrieksinstelling
(“poort dicht” = 5 sec.) weer actief.
Programmering openhoud- en voorwaarschuwingstijd
1. Druk de zwarte toets kort in. De lamp knippert 5x.
2. Wacht de gewenste openhoudtijd (min. 10-150 sec.)
af en druk daarna de zwarte toets kort in.
3. Wacht de in te stellen voorwaarschuwingstijd af
(min. 3-30 sec.). De lamp knippert opnieuw 5x.
Druk daarna nogmaals op de zwarte toets.
4. De programmering van de openhoud- en voorwaarschuwingstijd
is afgerond. Druk voor uitschakeling van de automatische sluiting
2x kort achter elkaar de zwarte toets in.
67
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner GA201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner GA201 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info