214407
35
Zoom out
Zoom in
Previous page
1/36
Next page
35
Additional information
English
Troubleshooting
Problem Cause Remedy
The projector does
not turn on.
There is no power from the power
cable.
Plug the power cable into the AC inlet on the
rear of the projector, and plug the power
cable into to the power outlet. If the power
outlet has a switch, make sure that it is
switched on. (See page 19)
The power switch is not in the on
position.
Put the power switch in the on position. (See
page 19)
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
The lamp cover is not securely
attached.
Correctly attach the lamp cover. (See page
33)
No picture.
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly. (See page
17)
The projector is not correctly
connected to the input source device.
Check the connection. (See page 17)
The input signal has not been
correctly selected.
Select the correct input signal with the
Source buttons on the remote control or
SOURCE / ENTER on the projector. (See
page 19)
Image is unstable.
The connection cables are not
securely connected to the projector or
the signal source.
Correctly connect the cables to the
appropriate terminals. (See page 17)
Picture is blurred.
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring. (See page 20)
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of this unit if necessary.
(See page 19)
The lens cap is still attached to the
lens
Remove the lens cap. (See page 19)
Remote control does
not work correctly
The batteries are out of power. Replace both of the batteries with new ones.
(See page 9)
There is an obstacle between the
remote control and the projector.
Remove the obstacle. (See page 13)
You are too far away from the
projector.
Stand within 8 meters (26.2 feet) of the
projector. (See page 13)
PE8720-en.book Page 35 Friday, May 13, 2005 5:19 PM
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ pe 8720 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ pe 8720 in the language / languages: English as an attachment in your email.

The manual is 3,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ pe 8720

BenQ pe 8720 User Manual - Dutch - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info