747164
9
Zoom out
Zoom in
Previous page
1/11
Next page
Dust and insect contamination
All smoke alarms and particularly the optical (photoelectric) type are prone to dust and
insect ingress which can cause false alarms.
The latest design, materials and manufacturing techniques have been used in the con-
struction of this Bellman & Symfon smoke alarm to minimize the eects of contamination.
However, it is impossible to completely eliminate the eect of dust and insect contamina-
tion, and therefore, to prolong the life of the smoke alarm you must ensure that it is kept
clean so that excess dust does not build up. Any insects or cobwebs in the vicinity of the
smoke alarm should be promptly removed.
In certain circumstances even with regular cleaning, contamination can build up in the
smoke sensing chamber causing the smoke alarm to sound. If this happens the smoke
alarm must be returned for servicing or replacement. Contamination is beyond our control;
it is totally unpredictable and is considered normal wear and tear. For this reason, contami-
nation is not covered by the warranty and a charge is made for all such servicing work.
End of life
When the battery starts to run out, the smoke alarm chirps and blinks every 40 s for a
minimum of thirty days.
Warning: The smoke alarm features a sealed non-replaceable battery. When the battery is
depleted you need to replace the unit.
Important: 10 years after the installation, the entire smoke alarm must be replaced. Check
the 'replace by' date marked on the side of the smoke alarm.
To protect our environment, batteries shall be disposed in a safe and environmentally
sound manner at your local recycle center.
Do not put the smoke alarm into a re
The smoke alarm should be disposed in a safe and environmentally sound manner at your
local recycle centre. Contact your local authority for further advice.
1716
Troubleshooting
If Try this
Nothing happens when I press the
smoke alarm test button.
Make sure the unit is installed properly, see 'Installa-
tion'. To turn it on, t the smoke alarm to the bracket
by turning it clockwise until is snaps into place.
If the smoke alarm is still not functioning properly
or if it is older than 10 years, it needs to be replaced.
Check the date on the 'replace by' label.
The smoke alarm beeps when I
press the test button, but the Visit
receiver is not responding.
Check the receiver batteries and connections.
Move the receiver closer to the smoke alarm to make
sure it’s within radio range.
The Visit receiver is activated for
no apparent reason.
Check for fumes, steam, etc. from the kitchen or
bathroom that can cause a nuisance alarm. Press
the test button to silence the alarm temporarily. The
status LED blinks every 8 s to conrm. If the problem
persists, it will sound the alarm after 10 minutes.
The smoke alarm chirps and blinks
in red every 40 s.
The smoke alarm battery is starting to run out.
Replace the unit.
The smoke alarm chirps every 40 s.
but it doesn’t blink in red.
Check for any sign of contamination such as
cobwebs or dust. If necessary, clean the unit, see
Cleaning your smoke alarm.
If the problem persists, the smoke alarm is defective
and needs to be replaced.
The interconnected smoke alarm
blinks and chirps once every 3 h.
The smoke alarm battery is starting to run out.
Replace the unit.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bellman BE1289 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bellman BE1289 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info