747165
11
Zoom out
Zoom in
Previous page
1/13
Next page
Troubleshooting
If Try this
The CO alarm beeps for no
apparent reason.
Follow the detailed instructions in What to do when the
alarm sounds section. If there are still problems:
Ensure there are no fuel burning appliances in the vicinity
which could be leaking CO gas (e.g. even from next door).
Ensure there are no fumes in the area (e.g. paint, thinners,
hair spray, chemical cleaners, aerosol sprays, damp proong
done with and aqueous emulsion such as amino functional
siloxane and alkylalkoxysilane.
Ensure there is no outdoor source of CO in the vicinity (e.g.
a car with engine running, heavy trac, heavy air pollution,
barbecue fumes etc.).
Ensure there is no source of hydrogen such as batteries being
charged (e.g. on boats or in Uninterruptable Power Supplies
(UPS)).
Ensure there is not excessive smoke or fumes from pipes,
especially those that use coal or charcoal.
Press the test/hush button to silence the alarm.
If the unit continues to sound it is possibly defective and
should be replaced.
The Visit receiver is triggered
for no apparent reason.
There is probably another Visit system nearby that triggers
yours. Change the radio key on all units, see Changing the
radio key.
Tamper proong the alarm
The alarm can be made resistant to unauthorized removal. Proceed as follows:
1 Break o the small pillar on the base.
2 To remove the alarm once installed, it is now necessary to use a small screwdriver, to release
the catch. Push the catch towards the ceiling and then twist o the alarm.
3 If necessary, it is possible to further secure or tamperproof the alarm by using a No.2 or
No.4 3/32" to 7/64" (2 to 3mm) diameter - not supplied self-tapping screw 1/4" to 5/16" (6 to
8mm) long to rmly lock the alarm and its mounting plate together.
1 2 3
19 20
If Try this
Nothing happens when I
press the CO alarm test/
hush button.
Check that the unit is secured correctly on the mounting plate.
Wait 15 s before testing again by pushing the test/hush button.
Check that the batteries are inserted correctly. Replace batteries.
Check the age of the alarm, see the “replace by label on the unit.
The CO alarm beeps when I
press the test/hush button,
but the receiver is not
responding.
Check the Visit receiver batteries and connections.
Move the receiver closer to the alarm to make sure it’s within range.
Check that the units are set to the same radio key, see
Changing the radio key.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bellman BE1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bellman BE1210 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info