772318
3
Zoom out
Zoom in
Previous page
1/8
Next page
1ATTACH MOUNT ONTO BIKE FRAME
1. Remove four (4) screws from back of
mount using 5mm Allen wrench.
2. Place front of mount around seat
tube of bike. Insert back of mount
to front of mount, insert screws.
Do not fully tighten. Do not place
around brake and derailleur cable
and housing.
CLICK RACK INTO MOUNT
1. Slide the ends of the carrier rack into the top holes on the mount. Once secured,
you will hear a click. This means the carrier rack is secured to the mount.
2. Slide the loose mount up or down until there is about 6 inches between rear wheel
and bottom of carrier. Be sure mount is centered along rear wheel facing forward.
3. Tighten the screws on the mount until mount will not slip up, down, or side to side.
4. Tighten fasteners securely, and check them frequently.
2
3
EASY, 3-STEP INSTALLATION
WARNING
Do not modify carrier rack or bicycle. If carrier rack will not t on your bicycle, consult your local bicycle dealer or
call our Customer Service at 1.800.456.BELL for assistance.
SEAT PAD INSTALLATION FOOT REST INSTALLATION
FOOT STRAP ATTACHMENT
1. Loop one piece of Velcro® through each foot rest and
attach back onto itself.
2. Insert top hooks of foot rests into opening along leg. Must
be at least three notches from bottom. Push to lower tabs
through respective opening and click into place. Lower
hook tabs need to be slightly lifted when inserted into slot.
Place seat pad into bottom of child carrier. Thread retention
harness through seat pad. Insert all four seat pad plugs into the
bottom of the child carrier.
To insert foot rest, insert top hook into preferred height. Slide
bottom tab into slot and pinch both together at the same time
while pushing the foot rest into place. Pull at them gently to
ensure they are secured properly. To remove foot rest, pinch
the hook and tab at the same time and pull up, freeing the
bottom tab. Then pull the top hook free.
Use harness slots at
child’s shoulders.
Shoulder straps should t snugly –
so that only one nger can t
between harness and shoulder.
Ensure top of chest clip is
positioned at armpit level.
Ensure harness forms the
shape of a V.
Connect each buckle end and
click to secure.
To release, pinch each side
of buckle and pull apart
buckle ends.
WARNING
Child can fall out of child carrier if harness is not correctly
fastened and adjusted.
RETENTION HARNESS:
3-POINT HARNESS
REFLECTOR INSTALLATION
To install the reector, remove backing paper on the reector
and place the sticky side onto the hexagonal molded imprint on
the back center of the child carrier. Press to adhere.
4 | English 5 | English
ATTACH RACK TO CARRIER
1. Turn the carrier upside down. Insert
suspension rack bars through holes
as shown below.
2. Insert the locking pin through the
holes under the carrier with the lever
in the unlocked position until it snaps
into place.. Turn the pin 180 degrees
untill it snaps into the locked position.
1
2
UNLOCKED LOCKED
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bell Shell at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bell Shell in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info