630716
4
Zoom out
Zoom in
Previous page
1/8
Next page
Corner installation Fig. 3
For corner installation, dimension D must be taken into
consideration. Dimension E is dependent on the thickness of
the unit front and the handle.
Connecting the appliance to the power supply
Before using the appliance for the first time, make sure that
the domestic power line is equipped with a conductor which
complies with the relevant safety regulations. The appliance
must only be connected by a qualified electrician and must
comply with the statutory and official provisions, as well as the
provisions of the local network operator.
In rare cases, failure of a conductor or an incorrect installation
may cause material damage or serious injury (death or injury
due to electric shock). The manufacturer accepts no
responsibility for personal injuries or damage to the appliance
due to faulty or incorrect electrical connection.
During all installation work, the appliance must be
disconnected from the power supply.
The appliance fulfils the requirements of protection class I and
may only be connected to an earthed mains socket.
The mains connecting cable must be at least type H05 V V-F
3G, 1.5 mm².
The yellow-green conductor must be connected first and be
slightly longer than the two other wires on the appliance side.
In accordance with safety regulations, an all-pole separator
with at least a 3 mm contact opening must be provided. A
separator is not required during connection, which is carried
out via an earthed power socket which is easily accessible at
all times.
Contact protection must be ensured during installation.
Determine the phase conductor and neutral conductor (zero
conductor) in the socket. The appliance may be damaged if
incorrectly connected.
The oven must be connected in accordance with the
information on the rating plate.
Place the appliance in front of the conversion cabinet to
connect it. The service cable must be long enough.
Caution: During installation, ensure that the mains cable is not
jammed and does not come into contact with hot appliance
parts.
All work on the appliance, including replacing the cabling,
must only be carried out by technical support.
UK and Australia only
Do not connect using a 13 A plug or protect with a 13 A fuse.
Only in Sweden, Finland and Norway
The appliance can also be connected using the plug provided
which has an earthing contact system. This must still be
accessible after installation. If this is not the case, an all-pole
isolating switch must be used on the installation side with a
contact gap of at least 3 mm.
Screwing the oven to the conversion cabinet - Fig.
5
Slide the appliance fully into the conversion cabinet. The
mains cable must not be laid over sharp edges or underneath
the oven, be jammed, bent or squashed, and must not come
into contact with hot appliance parts.
Align the oven centrally in the conversion cabinet and screw in
using the screws provided (4 x 25).
If the conversion cabinet corresponds to the dimensions
specified by us, there must be a ventilation slot above the
oven. To ensure sufficient ventilation, never cover this
ventilation slot.
A safety distance of at least 5 mm is required between the
appliance and the adjacent kitchen walls and units.
Removal
Disconnect the appliance from the power supply. Undo the
securing screws. Raise the appliance slightly and pull it out
completely.
nl
é
Installatievoorschrift
Belangrijke aanwijzingen
Wordt het apparaat onder een kookplaat ingebouwd, neem dan
het installatievoorschrift voor de kookplaat in acht.
Deurgreep niet gebruiken voor het transport of de inbouw van
het apparaat.
Apparaat voor de inbouw controleren op transportschade.
Bij alle montagewerkzaamheden dient het apparaat
spanningsloos te zijn.
Meubel voorbereiden - Afbeelding 1
Alleen een vakkundige inbouw volgens dit
installatievoorschrift garandeert een veilig gebruik. Bij schade
door een verkeerde inbouw is de monteur aansprakelijk.
Inbouwmeubels dienen bestand te zijn tegen een temperatuur
van 90 °C, aangrenzende voorzijden van meubels tegen een
temperatuur van 70 °C.
Alle uitsnijdingswerkzaamheden aan het meubel en het
werkblad uitvoeren voordat de apparaten worden ingebracht.
Spanen verwijderen, deze kunnen invloed hebben op de
werking van elektrische componenten.
Voorzichtig bij het inbouwen! Delen die tijdens het inbouwen
toegankelijk zijn, kunnen scherpe randen hebben. Draag
werkhandschoenen ter voorkoming van snijwonden.
Het aansluitstopcontact van het apparaat dient zich in het
gebied van het gearceerde vlak B of buiten de inbouwruimte
te bevinden.
Tussen het apparaat en de aangrenzende voorzijden van
meubels dient een luchtspleet van minstens 5 mm aanwezig
te zijn.
Niet bevestigde meubelen met een gebruikelijke, in de handel
verkrijgbare haak C aan de wand bevestigen.
Apparaat onder werkblad - Afbeelding 1
Voor het tussenschot van de ombouwkast is een ventilatie-
uitsnijding nodig.
Het werkblad bevestigen op het inbouwmeubel.
Wordt de inbouwoven onder een kookplaat ingebouwd, neem
dan het installatievoorschrift voor de kookplaat in acht.
Apparaat in bovenkast - Afbeelding 2+4
Het apparaat kan ook in een bovenkast worden ingebouwd.
Voor de ventilatie van de oven dient er tussen het tussenschot
en de plaatsingswand een spleet van ca. 20 mm te zijn.
Het apparaat niet te hoog inbouwen, zodat de bakplaten er
zonder probleem uitgenomen kunnen worden.
Hoekinbouw Afbeelding 3
Bij hoekinbouw de afmetingen D in acht nemen. De maat E is
afhankelijk van de dikte van het meubelfront en de greep.
Apparaat aansluiten op het elektriciteitsnet
Zorg er voordat u het apparaat voor het eerst gebruikt voor
dat de hoofdleiding volgens voorschrift geaard is. De
aansluiting van het apparaat mag alleen door een
gekwalificeerde elektrotechnicus worden uitgevoerd en dient
zowel te voldoen aan de wettelijke regels als aan de
overheidsvoorschriften en de bepalingen van de plaatselijke
netbeheerder.
Het ontbreken van een geaarde leiding of een onjuist
uitgevoerde installatie kan in zeldzame gevallen leiden tot
materiële schade of ernstig letsel (overlijden of letsel door een
elektrische schok). De producent is niet aansprakelijk voor
persoonlijk letsel of schade aan het apparaat veroorzaakt door
een ondeskundig uitgevoerde elektrische aansluiting.
Bij alle montagewerkzaamheden dient het apparaat
spanningsloos te zijn.
Het apparaat voldoet aan veiligheidsklasse I en mag
uitsluitend op een geaard stopcontact worden aangesloten.
De netaansluiting dient minstens van het type H05 V V-F 3G
1,5 mm² te zijn.
De geel-groene aardleiding dient eerst aangesloten te worden
en bij het apparaat wat langer dan de beide andere draden te
zijn.
Volgens de veiligheidsvoorschriften moet er een schakelaar
met een contactopening van minstens 3 mm voorhanden zijn.
Bij aansluitingen die via een geaard en altijd makkelijk
bereikbaar stopcontact worden uitgevoerd is geen schakelaar
vereist.
Tijdens de montage moet voorzien zijn in een
aanrakingsbeveiliging.
Bepaal wat de fasen en de neutrale leidingen (nulledingen) in
het aansluitstopcontact zijn. Bij een verkeerde aansluiting kan
het apparaat beschadigd raken.
De oven dient te worden aangesloten volgens de gegevens
op het typeplaatje.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Belion HBO604R10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Belion HBO604R10 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Belion HBO604R10

Belion HBO604R10 User Manual - English, Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info