579431
32
Zoom out
Zoom in
Previous page
1/36
Next page
32 / EN
Washing Machine / User’s Manual
indicator and Start / Stop LED continue to flash.
Also, when the loading door is ready to be opened, Loading
Door light will also turn off in addition to the programme step
light.
4.11.2 Changing the auxiliary function, speed
and temperature
Depending on the step the programme has reached, you
can cancel or select the auxiliary functions. See, "Auxiliary
function selection".
You can also change the speed and temperature settings.
See, "Spin speed selection" and "Temperature selection".
C
If no change is allowed, the relevant light will flash
for 3 times.
4.11.3 Adding or taking out laundry
1. Press the Start / Pause button to switch the machine
to pause mode. The programme follow-up light of the
relevant step during which the machine was switched into
the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the Loading Door and add or take out the laundry.
4. Close the Loading Door.
4. Make changes in auxiliary functions, temperature and
speed settings if necessary.
6. Press Start/Pause button to start the machine.
4.12 Child Lock
Use Child Lock function to prevent children from tampering
with the machine. Thus you can avoid any changes in a
running programme.
C
You can switch on and off the machine with On
/ Off
button when the Child Lock is active. When
you switch on the machine again, programme will
resume from where it has stopped.
4.12.1 To activate the child lock:
1. Press and hold Auxiliary Function button 2 for 3
seconds. In the programme selection display on the panel,
"Child lock enabled" light will turn on. You can release
Auxiliary Function button 2
when this warning is
displayed.
4.12.2 To deactivate the child lock:
1. Press and hold Auxiliary Function button 2 for 3
seconds. In the programme selection display on the panel,
"Child lock enabled" light will turn off.
4.13 Canceling the programme
The programme is cancelled when the machine is turned off
and on again. Press and hold
On / Off button for 3 seconds.
C
If you press On / Off button when the Child Lock is
enabled, the programme will not be cancelled. You
should cancel the Child Lock first.
If you want to open the loading door after you have
cancelled the programme but it is not possible
to open the loading door since the water level in
the machine is above the loading door opening,
then turn the
Programme Selection knob to
Pump+Spin programme and discharge the water
in the machine.
4.14 End of programme
End LED appears on the display when the programme is
completed.
If you do not press any button for 10 minutes, the machine
will switch to OFF mode. Display and all indicators are turned
off.
Completed programme steps will be displayed if you press
On / Off button.
4.15 Your machine features "Standby Mode".
After you switch on your machine with On-Off button, if no
program is started or no other procedure is performed at
the selection step or no action is taken within approx. 10
minutes after the selected program ends, your machine will
switch to OFF mode automatically. Display and all indicators
are turned off. Selected programme data will be displayed
if you press On / Off button. Before you start the program,
check the accuracy of your selections. If necessary, repeat
them. This is not an error.
5 Maintenance and cleaning
Service life of the product extends and frequently faced
problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
Lift the rear part of the siphon to remove it as illustrated.
C
If more than normal amount of water and softener
mixture starts to gather in the softener compartment,
clean the siphon.
2 Wash the detergent drawer and the siphon with plenty of
lukewarm water in a washbasin. Wear protective gloves
or use an appropriate brush to avoid touching of the
residues in the drawer with your skin when cleaning.
3 After cleaning, replace the siphon back to its seating and
push its front section downwards to make sure that the
locking tab engages.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate in
your machine in time and may cause unpleasant odours and
washing complaints. To avoid this, use the
Drum Cleaning
programme. If your machine is not featured with
Drum
Cleaning
programme, use Cottons-90 programme and
select
Additional Water or Extra Rinse auxiliary functions
as well. Run the programme without any laundry in the
machine. Before starting the programme, put max. 100
g of powder anti-limescale into the main wash detergent
compartment(compartment nr. 2). If the anti-limescale is in
tablet form, put only one tablet into compartment nr. 2. Dry
the inside of the bellow with a clean piece of cloth after the
programme has come to an end.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WMY 81483 LMB2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WMY 81483 LMB2 in the language / languages: English, German as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BEKO WMY 81483 LMB2

BEKO WMY 81483 LMB2 User Manual - Dutch, French - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info