542753

Behringer Xenyx X1222USB Manual

5
Zoom out
Zoom in
Previous page
1/16
Next page
5 XENYX X1222USB User Manual
1.2 The user’s manual
The user’s manual is designed to give you both an overview of the controls, as
well as detailed information on how to use them. In order to help you understand
the links between the controls, we have arranged them in groups according to
their function.
1.3 Before you get started
1.3.1 Shipment
Your mixing console was carefully packed in the factory to guarantee safe
transport. Nevertheless, we recommend that you carefully examine the
packaging and its contents for any signs of physical damage, which may have
occurred during transit.
◊ If the unit is damaged, please do NOT return it to us, but notify your
dealer and the shipping company immediately, otherwise claims for
damage or replacement may not be granted.
1.3.2 Initial operation
Be sure that there is enough space around the unit for cooling purposes and to
avoid over-heating. Please do not place your mixing console on high-temperature
devices such as radiators or power amps. The console is connected to the mains
via the supplied power cable. The console meets the required safety standards.
Blown fuses must only be replaced by fuses of the same type and rating.
◊ Please note that all units must be properly grounded. For your own
safety, you should never remove any ground connectors from electrical
devices or power cables, or render them in operative.
◊ Please ensure that only qualified people install and operate the
mixing console. During installation and operation, the user must have
sufficient electrical contact to earth, otherwise electrostatic discharges
might affect the operation of the unit.
1.3.3 Online registration
Please do remember to register your new BEHRINGER equipment right after your
purchase by visiting behringer.com (alternatively behringer.de) and kindly read
the terms and conditions of our warranty carefully.
Should your BEHRINGER product malfunction, our goal is to have it repaired as
quickly as possible. To arrange for warranty service, please contact the retailer
from whom the equipment was purchased. Should your BEHRINGER dealer not
be located in your vicinity, you may directly contact one of our subsidiaries.
Corresponding contact information is included in the original equipment
packaging (Global Contact Information/European Contact Information).
Shouldyour country not be listed, please contact the distributor nearest
you. Alist of distributors can be found in the support area of our website
(behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims quicker and more eciently.
Thank you for your cooperation!
2. Control Elements and Connectors
This chapter describes the various control elements of your mixing console.
Allcontrols, switches and connectors will be discussed in detail.
2.1 Mono channels
2.1.1 Microphone and line inputs
Fig. 2.1: Connectors and controls of mic/line inputs
MIC
Each mono input channel oers a balanced microphone input via the XLR
connector and also features switchable +48 V phantom power supply for
condenser microphones. The XENYX preamps provide undistorted and noise-free
gain as is typically known only from costly outboard preamps.
◊ Please mute your playback system before you activate the phantom
power supply to prevent switch-on thumps being directed to your
loud speakers. Please also note the instructions in chapter 2.5
“Rear view of X1222USB”.
LINE IN
Each mono input also features a balanced line input on a ¼" connector.
Unbalanced devices (mono jacks) can also be connected to these inputs.
◊ Please remember that you can only use either the microphone
or the line input of a channel at any one time. You can never use
both simultaneously!
INSERT
Insert points enable the processing of a signal with dynamic processors or
equalizers. They are sourced pre-fader, pre-EQ and pre-aux send. Unlike reverb
or other eects devices, whose signals are usually added to the dry signal,
dynamicprocessors are most eective on the complete signal. In this case,
auxsend paths are a less-than-perfect solution. It is better to interrupt the
signal path and insert a dynamic processor and/or equalizer. After processing,
the signal is routed back to the console at precisely the same point it left.
However, thechannel signal path is interrupted only if a plug is inserted into the
corresponding jack (stereophone plug: tip = signal output; ring = return input).
All mono input channels are equipped with inserts.
Inserts can also be used as pre-EQ direct outputs, without interrupting the signal
path. To this end, you will need a cable tted with mono phone plugs on the tape
machine or eects device end, and a bridged stereo phone plug on the console
side (tip and ring connected).
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx X1222USB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx X1222USB in the language / languages: English as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx X1222USB

Behringer Xenyx X1222USB Quick start guide - German, Dutch, Italian, Polish, Portuguese, Swedish - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info