542739

Behringer Xenyx 1832FX Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
ENGLISH
XENYX 1622FX/1832FX/2222FX/2442FX User Manual
8
ENGLISH
XENYX 1622FX/1832FX/2222FX/2442FX User Manual
9
BAL
The BAL(ANCE) control has a similar function to the PAN
control in the mono channels.
The balance control determines the levels of the left and
right input signals relative to each other before both signals
are routed to the left/right main mix bus (or odd/even
subgroup).
The remaining control elements in the stereo channels
perform the same functions as their counterparts in the
mono channels (MUTE switch, MUTE and CLIP LEDs, SOLO
switch, SUB and MAIN switches and channel fader).
Interface panel and main section2.3
Where it was useful to trace the signalow from top to
bottom in order to gain an understanding of the channel
strips, we now look at the mixing console from left to right.
The signals are, so to speak, collected from the same point
on each of the channel strips and then routed to the main
section all together.
MON control, aux sends 1, 2 and 3 (FX)2.3.1
Turning up the AUX 1 control in a channel routes the signal
to the aux send bus 1.
As the 1832FX is equipped with an additional monitor ◊
path, itsrst aux control in the channel strips is named
MON. The console also has a dedicated master fader
(MON SEND) for this aux path.
AUX SEND 1, 2 and 4
The AUX SEND 1 control governs the master send level of the
mix created by the individual channel AUX 1 sends.
Likewise, the AUX SEND 2 contol is the master control for the
aux 2 bus, and AUX SEND 4 controls the AUX 4 bus.
Fig. 2.7: The AUX SEND controls of the main section!
AUX SEND 3 (FX)
The FX control determines the signal level for eects
processing, i.e. regulates the level to an external (or the inter-
nal) eects device.
1622FX and 1832FX: On these consoles, this function is
performed by the AUX SEND 2 control (FX).
SOLO
You can use the SOLO switch to separately monitor the aux
sends via the CONTROL ROOM/PHONES outputs and check
these with the level meters.
If you want to monitor the signal of just one AUX bus, ◊
none of the other SOLO SWITCHES should be pressed
and the MODE switch should be in the SOLO position
(not depressed).
Aux send jacks2.3.2
Fig. 2.8: Aux send jacks
AUX SEND jacks
The AUX SEND jack should be used when hooking up a
monitor power amp or active monitor speaker system. The
relevant aux path should be set pre-fader.
On the 2222FX, aux send 1 is hard wired as pre-fader ◊
and hence called MON. Model 1832FX has a dedicated
monitor output (MON OUT jack), cf. chapter 2.3.4.
As already mentioned, the aux sends in the channels—if
set post-fader—can be used to connect to external eects
devices.
AUX SEND (FX)
The AUX SEND (FX) jack carries the master aux mix (from the
channel’s FX controls). You can connect this to an external
eects device to process the FX bus. The processed signal
can then be brought from the eects device back into the
STEREO AUX RETURN jacks.
Stereo aux return connectors2.3.3
Fig. 2.9: The aux return connectors
XENYX2442FX
XENYX2442FX XENYX1832FX
XENYX2442FXXENYX1832FX
On the 2222FX, 1832FX and 1622FX the STEREO AUX ◊
RETURN jacks are located on the front panel of the unit.
STEREO AUX RETURN
The STEREO AUX RETURN 1 jacks generally serve as the
return for the eects mix (created using the post-fader
aux sends) by connecting the output of an external eects
device. If only the left jack is connected, the AUX RETURN is
automatically switched to mono.
You can also use these jacks as additional line inputs.◊
All stereo aux returns are balanced, but can of course also
be used with unbalanced connectors. If you use an aux send
for monitoring, the associated unused stereo aux returns are
available for other line level signals (e.g. keyboards).
A signal fed into the stereo return jacks can be output ◊
via an aux send jack. More information on this can be
found in chapter 2.3.5 “STEREO AUX RETURN 1/2 (TO
AUX SEND)”.
STEREO AUX RETURN FX
The STEREO AUX RETURN FX jacks accept the eects mix
return (created using the channel FX sends). If these jacks are
already in use as additional inputs, you can route the eects
signal back into the console via a dierent channel. The
advantage of this is that you can now use that channel’s EQ
on the eects return signal.
In this instance, the FX control of the channel being ◊
used as an eects return should be turned fully
counterclockwise, otherwise feedback problems could
occur!
If you wish to use the internal eects processor, do not ◊
plug any connectors into the STEREO AUX RETURN FX
jacks, unless you want to tap the processed signal via
the FX OUT (2222FX and 2442FX only).
The monitor section of the 1832FX2.3.4
One of the ways that the 1832FX diers from the other
models of this series is that it has a separate monitor output.
Fig. 2.10: Monitor output of the 1832FX
Therst aux send (MON) on this console is used to set up
the monitor mix from the channels and route it to the MON
SEND fader.
Fig. 2.11: Monitor fader of the 1832FX
MUTE
Press the MUTE switch to mute the monitor send.
SOLO
The SOLO switch routes the monitor send to the solo bus
(post-fader and post-mute) or to the PFL bus (pre-fader and
pre-mute). The position of the MODE switch in the main
section determines which of the buses is selected.
Stereo aux return control2.3.5
STEREO AUX RETURN 1
The STEREO AUX RETURN 1 control determines the level of
this signal in the main mix. If STEREO AUX RETURN 1 is used
as eects return, this will determine the level of the eects
when mixed with any “dry” channel signal.
When used in this way, the eects device should be set ◊
at 100% eect.
Fig. 2.12: Stereo aux return and stereo aux return (to aux send) controls
XENYX1832FX
XENYX1832FX
XENYX2442FX
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx 1832FX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx 1832FX in the language / languages: English as an attachment in your email.

The manual is 5,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx 1832FX

Behringer Xenyx 1832FX User Manual - Dutch - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info