660485
1
Zoom out
Zoom in
Previous page
1/2
Next page
DUAL A/B SWITCH AB200
Thank you for showing your confidence in us by purchasing
the BEHRINGER AB200. This high-quality 2-channel A/B switch
is designed for musicians who use several amps and/or
instruments. The AB200 allows you to switch between gear
noiselessly and instantaneously without coloring the sound of
your instrument. The LED always displays which element of
your system is currently being used.
1. CONTROLS AND CONNECTIONS
Fig. 1.1: Rear view
Since the controls and connections of the two channels are
identical, this chapter only describes channel 1.
IN/OUT 1: this 1/4" TS jack serves as channel 1 input when
a source is plugged in (guitar, bass etc.) and as channel 1
output when an amp or an effect is plugged in.
A1 & B1: these 1/4" TS jacks serve as channel 1 outputs
when amps or effects are plugged in; they serve as channel
1 inputs when instruments are plugged in. Only one of
these connectors can be active at any one time.
LATCH/NON LATCH: this selector determines the channel
switch function: when set to LATCH, the switch is latching.
When set to NON LATCH, the signal will only be routed to or
from B1 as long as you hold the pedal depressed.
4
Fig. 1.2: Top view
SWITCH 1: this switch allows you to assign the IN/OUT 1
signal to A1 or B1 when IN/OUT 1 is used as an input.
Otherwise, the switch assigns the A1 or B1 signal to
IN/OUT 1 when A1 and B1 are used as inputs. The A1 and
B1 LEDs display which connector is currently active.
Depending on the selector position, shortly press the
switch (LATCH) or hold it down during the whole commutation
time (NON LATCH) to toggle between A1 and B1.
To install or replace the 9 V battery, please carefully unscrew the
bottom plate and open the enclosure of the AB200. After installing
close the unit again by using all screws you removed before.
+ The AB200 has no on/off switch. As soon as you
insert a jack into the A1 or B1 connector, the AB200
begins running. When not using the AB200, remove
the jacks from the connectors. This extends the
life of the battery.
The SERIAL NUMBER is located at the bottom of the unit.
2. APPLICATIONS
Fig. 2.1: One instrument / two amps
Plug your instrument into IN/OUT 1 and the input of each amp
into one of the A1 and B1 connectors. Pressing the switch 1 will
toggle between the two amps.
Fig. 2.2: Two instruments / one amp
Plug each of your instruments into one of the A1 and B1
connectors and the amp input into IN/OUT 1. Pressing the switch
1 will toggle between the two instruments.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer AB200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer AB200 in the language / languages: English as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer AB200

Behringer AB200 User Manual - German - 2 pages

Behringer AB200 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info