301518
20
Zoom out
Zoom in
Previous page
1/21
Next page
43
Your washing machine is equipped with safety
functions, which can detect faults early and react
accordingly.
Often these are no more than minor problems
that can be solved quickly.
The appliance fails to start:
Please check whether:
The mains plug is inserted into the socket.
The socket is functioning correctly
(e.g. using a table lamp).
The appliance door is closed (child safety
device?).
A programme has been selected.
The “ON/OFF” button was pressed.
No or little water:
Press the “ON/OFF” button; the indicator light
will go out.
Please check whether:
The tap is turned on fully, the main water
supply (water pressure) is operational.
The inlet hose is kinked.
The mesh filter in the water hose is blocked
or dirty (see “Care and maintenance/water
hose filter”).
The water in the supply hose is frozen.
Press the “ON/OFF” button again to continue with
the programme.
Waste water not drained:
Press the “ON/OFF” button; the indicator light will
go out.
Please check whether:
The drain hose is installed without kinks
(see “Installation Instructions”) .
The pump or the filter is blocked
(see Removing the Filter / Draining Residual
Water”).
IMPORTANT:
Make sure that the water has
cooled before draining.
The water in the drain pipe is frozen.
Press the “ON/OFF” button again in order to
continue the programme.
If the fault occurs again, contact After-Sales
Service (see “After-Sales Service”).
If the water stop was released:
A released water stop can be recognised by the
fact that the water flow is interrupted and a
continuous pumping noise can be heard.
Switch off appliance and close tap.
If excess foam has caused the water stop,
the water collected in the base tray may be
drained by tilting the appliance forward
slightly.
If the water stop is activated again when the
appliance is switched on, contact the After-
sales service.
The appliance vibrates during the
spin cycle:
Please check whether:
The appliance is horizontal with all four feet
on the ground (see “Installation
Instructions”), and the lock nuts are tight.
The transit bolts have been removed.
Before using the appliance the transit bolts MUST
be removed (see “Installation Instructions”)
The laundry is not spun properly after
the programme has terminated or,
subsequently is not dried:
The in-built unbalance control system
recognises excessive unbalance at the start
of the spinning cycle (e.g. for small loads or
loads consisting of large items only). In this
case the appliance automatically terminates
the wash programme without final spin, in
order to avoid possible costly damage to the
appliance. In this case, the laundry will
remain damp after subsequent drying.
Are there larger amounts of foreign bodies in
the filter, or is the drain pump rotor blocked?
Carry out drainage if necessary.
TROUBLESHOOTING GUIDE
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wt 1530 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wt 1530 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht wt 1530

Bauknecht wt 1530 User Manual - English - 21 pages

Bauknecht wt 1530 User Manual - German - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info