53098
11
Zoom out
Zoom in
Previous page
1/13
Next page
63
Fault display table
a.Fault in the water supply
The appliance has no or insufficient water supply.
For models with a fault display, the “Water tap” lamp
lights up and (depending on model) the spin speed
indication lamps flash.
For models with no fault display, the washing machine
stops in the appropriate programme step.
Switch the appliance off and pull out the mains plug.
Check whether:
the water tap is fully turned on, and the water
supply pressure is sufficient
the water inlet hose is kinked
the water connection mesh filters are blocked
(see “Care And Maintenance”/”Mesh Filters in the
Water Connection”)
the water supply hose is frozen up
the washing machine has a safety hose and the
safety valve is open (red indicator in the safety valve
inspection window); In this case replace it with a
new safety hose
Reconnect the appliance to the electrical socket.
For models with a fault display, reselect the desired
programme and start it.
For models without a fault display continue the
programme by pressing the “On/Off” or the “Start” or
the “Start/Pause” button (depending on model) again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
b.Draining fault
Waste water not pumped out.
For models with a fault display the spin speed indication
lamps flash and the pump display flashes. If a digital display
is fitted, “P
” and “F” are also displayed alternately.
For models with no fault display, the washing machine
stops in the appropriate programme step.
Switch the appliance off and pull out the mains plug.
Check whether:
the drain hose is kinked
the pump or the filter is blocked (see “Removing
The Filter”)
IMPORTANT:
before draining, make sure that the
water has cooled down.
The water in the drain hose is frozen up
Reconnect the appliance to the electrical socket.
For models with fault display, select and start the
“Drain” cycle.
To rinse the laundry, we then recommend a short
programme without the addition of detergent.
For models without a fault display continue the
programme by pressing the “On/Off” button again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
c. Fault in an electrical component
The appliance stops in the middle of a programme.
For models with a fault display, the spin speed
indication lamps flash. If a digital display is fitted, “F4
” to
“F16
” are also displayed.
Switch the washing machine off. First of all select and
start the “Drain” cycle.
Then select and start the desired programme again.
For models with no fault display, the washing machine
stops in the appropriate programme step.
First switch the washing machine off and on again to
continue with the programme.
If the fault persists, please contact After-Sales Service
(see “After-Sales Service”).
d.“Water Stop” fault
(if fitted)
The “Water Stop” fault may have been triggered by:
1.
excess foaming
2.
a leak in the washing machine.
In this case the pump is switched on automatically in
order to pump the water out.
For models with a fault display, the “Water Stop”
indication flashes and the spin speed indication lamps
flash. If a digital display is fitted, “A
” and “F” are also
displayed alternately.
For models with no fault display, the washing machine
stops in the appropriate programme step.
Switch the appliance off, pull out the mains plug
and turn the water tap off.
Tilt the appliance forwards ( with 2 people it is
suggested), to allow the collected water to flow out
from the bottom of the appliance.
Then:
1.
Plug in the appliance.
2.
Turn the water tap on (if water immediately flows
into the appliance again, without the appliance being
started, there is a fault. Turn off the tap and notify
After-Sales Service).
3.
For models with fault display, select and start the
desired programme again.
For models with no fault display, continue the
programme by pressing the “On/Off” button again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
Luminous display
Spin
speed
lights
Digital display
(if fitted)
Fault description
“Water tap” flash “H” and “F” “Fault in water supply”
“Pump” flash “P” and “F” “Draining fault”
- flash from “F4” to “F16 “Fault in an electrical component
“Water Stop” flash “A” and “F” “Water Stop fault”
4GB05140.fm Page 63 Wednesday, April 14, 2004 12:18 PM
Black process 45.0° 100.0 LPI
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht WAK7990 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WAK7990 in the language / languages: English as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info