Manual Bauknecht WAE 9491 (page 2 of 2) (English)

519243

Zoom out

Zoom in

1/2

5019 401 05286

Add the detergent as described in the chapter

“Detergent and Additives” in the instructions for use.

1. Turn the programme selector knob to the

desired programme.

2. The remaining time display shows the duration

of the chosen programme (in hours and minutes),

and the lamp over the “Start” button flashes.

3. The programme sequence indicator and the

predefined spin speed indication corresponding to

the selected programme lights up.

The recommended temperature (see the indicator)

can be altered by pressing the temperature selection

button under the temperature display.

• Wash your laundry in the desired programme

(Cotton, Synthetics), adding an appropriate

amount of chlorine bleach to the SOFTENER

chamber (close the detergent dispenser carefully).

• Immediately after end of programme, start the “Rinse

and Spin” programme to eliminate any residual bleach

smell; if you want, you can add softener.

“Eco +” button

• With a modified temperature profile and a slightly

prolonged washing duration, the optimum

combination of excellent washing result and even

lower energy consumption can be achieved.

“Prewash” button

• Only for heavily soiled laundry (e.g. sand or

granular dirt). Programme duration is increased

by some 15 min.

“Intensive Rinse” button

• An additional rinse cycle is carried out.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with detergent allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water

without being spun: discoloration of the laundry

and additional creasing are prevented.

• This option is particularly recommended for the

programme “Synthetic” or “Delicate”.

• This function is particularly useful if you want to

postpone spinning to a later time.

Note: The programme has reached the “Rinse

Hold” when the corresponding light flashes.

Terminate the “Rinse Hold” option:

• Press the “Rinse Hold” button again; the

programme will terminate automatically with the

appropriate spin cycle for the current programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to “Drain” and press

the “Start” button again.

“Spin Speed Reduction” button

• A maximum spin speed is assigned to each

programme.

• Press the button to set another speed for the

spin cycle.

• If no light goes on, the final spin is cancelled.

The water is only drained out.

CONSUMPTION DATA

Programme Temperature

(°C)

Wash

(kg)

Water

(l)

Energy

(kWh)

Programme duration

approx.**

(hours : minutes)

Cotton White/Hygiene+

95 6.0 49

***

1.90 2:00

Cotton Colours

60 6.0 44 1.14 2:20

Cotton with “Eco +” ****

60 6.0 44 1.02 2:30

Cotton Colours

40 5.0 42 0.70 2:05

Synthetics

60 2.5 60

***

0.90 1:45

Synthetics

40 2.5 55 0.60 1:30

Daily Load

40 3.0 48 0.55 1:00

Quick Wash

30 3.0 37 0.30 0:30

Delicate

30 1.5 60 0.50 0:45

Wool

40 1.0 60 0.50 0:40

Handwash

30 1.0 45 0.40 0:35

Easy Ironing

40 3.0 60 0.60 1:30

* The consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60456.

** The programme duration may also vary from the chart values. The washing machine is able to allow for particular

household conditions and to adapt the programme run time accordingly.

*** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump

drains the water out.

**** Reference programme for energy label.

POUR IN DETERGENT, CLOSE THE

DOOR AND SELECT A PROGRAMME

USING CHLORINE BLEACH

SELECT SPECIAL OPTIONS -

The corresponding lights go on (if not

selectable: rapid flashing for 3 seconds)

With the “Start Delay” function the appliance can be

run cheaply e.g. at night, when the electricity is

cheaper.

• Press the “Start Delay” button. Select the

programme start from 1 to 24 hours ahead by

pressing the button again.

• Press the “Start” button.

The Start Delay indicator light flashes until the

programme starts.

“Start Delay” correction.

• Before “Start” has been pressed:

The preset number of hours can be altered by

continuously pressing the “Start Delay” button.

By pressing the Start Delay button again after the

“24” setting, the time delay can be deleted again

or set again.

After “Start” has been pressed:

The preset number of hours can be reduced by

pressing the “Start Delay” button again; please

note, however, that the washing programme

starts IMMEDIATELY, as soon as you operate it

again with the Start Delay switch 01 setting.

To increase the number of hours preselected,

first turn the programme selector switch to the

“Off” position. Then set the programme and the

additional options again and select the desired

number of hours.

After you have selected the programme and eventually

the additional options, the indicator light over the

“Start” button flashes. Turn on the tap and start the

programme by pressing the “Start” button. Now the

indicator light over the button goes on.

In addition, all programme phases are indicated by the

associated lights. After the end of a programme phase,

the associated indicator light goes out. Thus the

programme sequence indicator moves from left to

right across the wash, rinse and spin phases. At the end

of the programme, only the “End” indicator is still on.

As long as a washing programme is running, the

lamp lights up to show that the door cannot be

opened. When the lamp goes off, the door can be

opened again.

If “Start” has been pressed, but the door is not

latched, the “Door Locked” indicator flashes for 10

seconds. The door must be pushed shut within this

time.

After the 10 seconds, the “Door Locked” indicator

goes out and the “Start” button flashes. The door

must then be opened and closed again and the

“Start” button must be pressed.

“Pump”

Waste water is not pumped out. Check wether the

drain hose is kinked or the filter must be cleaned; in

the latter case refer to the Instructions for Use

(“Removing the Filter”).

“Water Tap”

The appliance has no or insufficient water supply.

Open the water tap; if the indication still lights up,

refer to the “Troubleshooting Guide" in the

Instructions for Use.

• The “End” indicator goes on.

1. Switch the washing machine off by turning the

programme selector to the “O”-position.

2. Turn off the tap.

3. Open the door and unload the machine.

A newly-selected programme will continue in the

same programme section during which the current

programme was interrupted. Therefore do not add

any more detergent.

1. Press the “Start” button to interrupt the

programme. The light flashes.

2. Select the new programme (with temperature),

any additional options and - if you wish - another

spin speed.

3. Press the “Start” button again to restart the

programme.

• If you are in the “Prewash” programme step, this

additional option cannot be deselected as

described (to do this see “Cancel/Reset a

running programme before the end”).

Press the “Reset” button for at least 2 seconds.

Any existing water is drained out before the door

can be opened.

START DELAY

PROGRAMME START

“DOOR LOCKED” INDICATOR

“TROUBLE” INDICATORS

PROGRAMME END

RESELECT AFTER PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

40105286GB.fm Page 2 Thursday, December 29, 2005 4:57 PM

Black process 45.0° 100.0 LPI

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WAE 9491 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WAE 9491

Bauknecht WAE 9491 User Manual - English - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bauknecht WAE 9491 Manual

Product: