Manual Bauknecht WAE 8759 (page 3 of 17) (English)

572356

Zoom out

Zoom in

1/17

5019 401 05518

Add detergent as indicated on the front page and as described in

the chapter “Detergent and Additives” in your Instructions for Use

(remove separator in detergent dispenser for use of powder

detergent if necessary).

Turn the programme selector to the desired programme; the light

of the

“Start (Pause)”

button blinks. The

temperature

and

spin

speed

indicated on the display can be altered by pressing the

“Temperature” button or the “Variable spin” button.

When the combination of programme and additional option(s) is

not possible, the indication lights switch off automatically.

Unsuitable combinations of options are deselected automatically.

“Clean+” button

• Choose this option if you use an in-wash additive for stain removal

(powder, for example “Vanish”) - it will optimize the additive’s

efficiency to get better wash performance and stain removal.

• Choose temperature of 30 or 40°C and use with maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together with

your detergent (only use powder detergent with this option).

Respect the manufacturer’s dosing instructions.

• Prolongs the programme by approx. 10 to 15 minutes.

• Appropriate for use of stain removers and bleaches on oxygen

basis.

Chlorine or perborate bleaches must not be used!

“Prewash” button

• Only for heavily soiled loads (for example sand, granular dirt)

sensible. Increases the cycle time by approximately 15 min.

• Do not use liquid detergent for the main wash when activating

the “Prewash” option.

“Rinse hold” button

• The laundry remains in the last rinse water, without

progressing to the fnal spin cycle, to avoid creasing and

prevent colours from changing.

• The programme stops to “Rinse hold” when the “Rinse hold”

symbol on the display blinks; the light of the

“Start

(Pause)”

button blinks as well.

• To terminate the “Rinse hold” by draining the water, without

any spinning, press the

“Start (Pause)”

button.

• To terminate the “Rinse hold” by spinning the laundry, press

the "Variable spin" button to select the desired spin speed and

then

“Start (Pause)”

to start the spin cycle.

• Do not leave the laundry to soak for too long in the “Rinse hold”.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very soft water or

for washing baby linen, and helps people with allergies.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is cancelled but

intermediate spin peaks remain during rinse. The water is

drained out only.

If there is a programme setting which you use frequently, the

appliance offers the possibility to save one setting for each

programme so that it can be used again by just pushing one button.

• Select the desired programme, temperature, spin speed and

option(s), push and hold the

“Favourites”

button for at least 3

seconds. The lamp of the

“Favourites”

button shortly blinks and

then lights up - the programme setting is saved.

CONSUMPTION DATA

Programme

Te m pe r a t u r e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

White Cotton / Hygiene + 95 8.0 82

2.40 2:20

Coloured Cotton 60 8.0 59 1.36 2:20

Coloured Cotton 40 8.0 77 0.75 2:05

Synthetics 60 3.5 46

0.85 1:35

Synthetics 40 3.5 42 0.50 1:20

Delicates 30 2.5 60 0.40 0:45

Wool 40 2.0 60 0.60 0:45

Handwash 40 2.0 45 0.60 0:40

Lingerie 30 2.0 45 0.35 0:36

Eco Cotton

***

60 8.0 59 1.04 4:00

Sport 30 3.5 54 0.55 1:34

Super Eco 60 8.0 75 0.95 4:00

Daily load 40 6.0 73 0.60 1:00

Speed 15 30 3.0 30 0.20 0:15

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions

applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label (with separator in detergent dispenser removed for use of powder detergent).

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

SAVE YOUR FAVOURITE PROGRAMMES

Next time you want to use your individual programme setting,

select the programme, shortly push the

“Favourites”

button and

start by pushing

“Start (Pause)”

If you want to replace the saved programme setting by another

one, proceed as already described above.

The “Start delay” allows to run the machine at the consumer’s

convenience, for example at night when electricity is cheaper. Do

not use liquid detergent when activating the “Start delay”.

• Select programme, temperature, spin speed and options.

• Press the Start delay button to select one of the delay time

steps between 0:30 and 23:00 hours.

• Press the

“Start (Pause)”

button; the light stops blinking and

becomes solid.

The countdown of the delay time begins; the clock symbol next to

the delay time and the colon between hours and minutes blink.

• The time delay indication disappears when the programme

starts and it is replaced by the remaining programme time.

To cancel the “Start delay”

..before you press the “Start (Pause)” button:

• Press the

“Reset/Drain”

button, or set the start delay time to

“0:00” - the delay time disappears after a few seconds.

..after having pressed the “Start (Pause)” button:

Press the

“Start (Pause)”

button - the delay time disappears

from the display; press

“Start (Pause)”

again to start the selected

programme immediately.

Before starting and after end of a programme, the symbol lights to

show that the door can be opened. As long as a wash programme is

running, the door remains locked and must on no account be forced

open. In case you have to open it urgently during a running

programme, refer to “Reset a running programme before the end”.

Open the tap and press the

“Start (Pause)”

button; the blinking

“Start (Pause)”

button light becomes constant. The programme

sequence indicator shows the current programme phase, running

from left to right through wash, rinse, spin, drain. In some phases, the

remaining programme time is newly calculated - if this is the case, the

“green intelligence sensor” on the display will fade,

and the remaining time is replaced by an animation.

Activating the child lock prevents children from starting a wash

cycle or changing the settings of a running programme. The child

lock cannot be activated or deactivated when the programme

selector is in the “Off/O” position. To activate the child lock:

• Turn the programme selector to a programme position, or run

a programme as usual.

• Press the “Temperature” and the “Variable spin” button

simultaneously for at least 3 seconds. The “Child lock” symbol

will shortly blink and then light up to indicate that the

child lock is active.

The programme setting cannot be changed anymore; the only change

possible is to switch the washer off by turning the programme selector

to the “Off/O” position. To deactivate the child lock, proceed in the

same way as for activating it.

If one of the red failure indications on the display lights up, refer to

the “Troubleshooting Guide” in your “Instructions for Use”.

• The display shows “End”, and the “Door open” indication

lights up.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

• Leave the door ajar to allow the drum to dry.

• If you do not turn the programme selector to the “Off / O”

position, all lights of the control panel go out after a few minutes

to save energy - only “End” will remain on the display.

The symbol will light up at the end of the programme if you used

too much detergent. Use less detergent next time. If the symbol

lights up and the display shows “Fod”, too much foam interrupted

the wash process; refer to the “Troubleshooting Guide” in your

Instructions for Use.

1. Press the

“Start (Pause)”

button to pause the programme.

The light blinks.

2. Select the new programme, temperature, any options and

another spin speed if you want.

3. Press the

“Start (Pause)”

button again. The new programme

continues at the same position where the previous programme was

interrupted. Do not add detergent for this programme.

The

“Reset/Drain”

button cancels a programme before the end.

• Press the

“Reset/Drain”

button for at least 3 seconds; an

animation appears on the display. Any existing water is drained

out before the door can be opened.

START DELAY

“DOOR OPEN” INDICATION

PROGRAMME START

CHILD LOCK

RED FAILURE INDICATIONS

PROGRAMME END

DETERGENT OVERDOSAGE INDICATION

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

The Sensor Technology automatically adapts Programme Time, Water and Energy consumption to the size of your wash load.

40105518GB.fm Page 2 Friday, November 27, 2009 3:07 PM

Black process 45.0° 150.0 LPI

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WAE 8759 in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WAE 8759

Bauknecht WAE 8759 User Manual - German - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bauknecht WAE 8759 Manual

Product: