Manual Bauknecht WAE 8749 (page 3 of 17) (English)

572355

Zoom out

Zoom in

1/17

5019 401 05517

Load your laundry, close the door properly and add detergent as

indicated on the front page and as described in the chapter “Detergent

and Additives” in your Instructions for Use (remove separator in

detergent dispenser for use of powder detergent if necessary).

1. Turn the

programme selector

to the desired programme. The

display shows the programme duration in hours and minutes as well as

the predefined temperature. The

“Start (Pause)”

button blinks.

2. The

temperature

can be altered by pressing the

“Temperature” button.

3. The indication lamp of the predefined

spin speed

lights up; in case

you want to set another spin speed, press the “Variable spin” button.

Push the button(s) of any option(s) desired - the respective

indication lights up.

When the combination of programme and option is not possible,

the lights switch off automatically. Unsuitable combinations of

options are deselected automatically.

“Clean +” button

• Choose this option if you use an in-wash additive for stain removal

(powder, for example “Vanish”) - it will optimize the additive’s

efficiency to get better wash performance and stain removal.

• Choose temperature of 30 or 40°C and use with maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together with

your detergent (only use powder detergent with this option).

Respect the manufacturer’s dosing instructions.

• Prolongs the programme by approx. 10 to 15 minutes.

• Appropriate for use of stain removers and bleaches on oxygen

basis.

Chlorine or perborate bleaches must not be used!

“Prewash” button

• Only for heavily soiled loads (for example sand, granular dirt)

sensible. Increases the cycle time by approximately 15 min.

• Do not use liquid detergent for the main wash when activating

the Prewash option.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very soft

water, washing baby linen and helping people with allergies.

“Easy ironing” button

• Reduces creasing by an increased water quantity and a very

gentle spin.

“Rinse hold” button

• Press the button if you want to postpone spinning to a later

time or if you want to drain only.

• The laundry will remain in the last rinse water without

progressing to the final spin cycle to avoid creasing and prevent

colours from changing.

• Do not leave the laundry to soak in the “Rinse hold” for too long.

• The washing machine stops to rinse hold as soon as the “Rinse

hold” light in the programme sequence indicator blinks; the

“Start (Pause)”

button also blinks.

To terminate the “Rinse hold”:

• If you want to drain only without spinning: Press the

“Start

(Pause)”

button to start the drain process.

• If you want to spin your laundry: Press the “Variable spin”

button to select the desired spin speed and then

“Start

(Pause)”

to start the spin cycle.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If you select spin speed “0”, the final spinning is cancelled but

intermediate spin peaks remain during rinse. The water is

drained out only.

CONSUMPTION DATA

Programme

Te mp er at u re

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

White Cotton / Hygienic + 95 8.0 82

2.40 2:20

Coloured Cotton

60 8.0 59 1.36 2:20

Coloured Cotton 40 8.0 77 0.75 2:05

Synthetics 60 3.5 46

0.85 1:35

Synthetics 40 3.5 42 0.50 1:20

Delicates 30 2.5 60 0.40 0:45

Wool 40 2.0 60 0.60 0:45

Handwash 40 2.0 45 0.60 0:40

Lingerie 30 2.0 45 0.35 0:36

Eco Cotton

***

60 8.0 59 1.04 4:00

Sport 30 3.5 54 0.55 1:34

Super Eco 60 8.0 75 0.95 4:00

Daily load 40 6.0 73 0.60 1:00

Speed 15 30 3.0 30 0.20 0:15

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary

with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label (with separator in dispenser removed for powder detergent use).

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

The “Start delay” allows to run the machine at the consumer’s

convenience, for example at night when electricity is cheaper. Do

not use liquid detergent when activating the “Start delay”.

• Select programme, temperature and options.

• Press the “Start delay” button to select a delay time up to 23

hours; the light of the

“Start (Pause)”

button blinks.

•Press the

“Start (Pause)”

button; the countdown of the delay

time begins. The light of the

“Start (Pause)”

button stops

blinking and is on; the light of the start delay button will keep

blinking until the programme starts.

• As soon as the programme starts, the start delay on the display

is replaced by the remaining programme time, and the light of

the “Start delay” button goes off.

• Once having pressed the

“Start (Pause)”

button, the number

of hours preselected can be changed by pressing and holding

the “Start delay” button.

To cancel the “Start delay”

..before you press “Start (Pause)”:

• Turn the programme selector to another position or press the

“Reset/Drain”

button.

..after having pressed “Start (Pause)”:

•Press

“Start (Pause)”

- the delay time disappears from the

display; press

“Start (Pause)”

again to start the selected

programme immediately.

Open the tap and press

“Start (Pause)”

; the light stops blinking and is on.

The programme sequence indicator shows the current programme

phase, running from left to right through Wash, Rinse, Spin/Drain.

The display shows the remaining programme time. Due to

variations in load and temperature of inlet water, the remaining

time is newly calculated in certain programme phases. If this is the

case,

an animation appears on the display

Activating the child lock prevents children from starting a wash

cycle or changing the settings of a running programme. The child

lock cannot be activated or deactivated when the programme

selector is in the “Off/O” position. To activate the child lock:

• Turn the programme selector to a programme position, or run

a programme as usual.

• Press the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds; a key-like symbol will shortly

appear on the display to indicate that the child lock is active.

Any time you try to change a programme setting with active child

lock, the display will shortly show the key-like symbol. The

programme setting cannot be changed anymore; the only change

possible is to switch the washer off by turning the programme

selector to the “Off/O” position. To deactivate the child lock:

• Press again the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds.

Before starting and after end of a programme, the lamp lights to show

that the door can be opened. As long as a wash programme is running,

the door remains locked and must on no account be forced open. In

case you have an urgent need to open it during a running programme,

refer to “Reset a running programme before the end”.

“Service”

Lighting up of the “Service” indication can be caused by a fault in an

electrical component. Refer to the “Troubleshooting Guide” in your

Instructions for Use; if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open the water

tap; if the indication still lights up, refer to the “Troubleshooting

Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain hose is

kinked or the filter must be cleaned; in the latter case refer to the

Instructions for Use (“Removing the Filter”).

• The display shows “End” and the “Door open” indication lights.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

• Leave the door ajar to allow the drum to dry.

In case you used too much detergent, a small vertical bar will light

next to the overdosage symbol on the right of the display when

the wash programme is finished; use less detergent next time. Too

much foam by detergent overdosing can also lead to interruption

of a wash cycle; in this case the display shows “Fod” - follow the

recommendations in the “Troubleshooting Guide” in your

Instructions for Use to solve the problem.

1. Press

“Start (Pause)”

to pause the programme; the light

blinks.

2. Select the new programme, temperature, any options and

another spin speed if you want.

3. Press

“Start (Pause)”

again. The light is on, and the programme

continues at the same position where the previous programme was

interrupted. Do not add detergent for this programme.

The

“Reset/Drain”

button cancels a programme before the end.

•Press the

“Reset/Drain”

button for at least 3 seconds; “rES”

appears on the display. Any existing water is drained before

the door can be opened.

START DELAY

PROGRAMME START

CHILD LOCK

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

DETERGENT OVERDOSAGE INDICATION

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

The sensor Technology automatically adapts Programme Time, Water and Energy consumption to the size of your wash load.

40105517GB.fm Page 2 Thursday, November 26, 2009 4:57 PM

Black process 45.0° 150.0 LPI

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WAE 8749 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WAE 8749

Bauknecht WAE 8749 User Manual - German - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bauknecht WAE 8749 Manual

Product: