Manual Bauknecht WA 8511 (page 3 of 3) (English)

572347

Zoom out

Zoom in

1/3

5019 401 15306

Add the detergent as described in the programme table or in the

chapter “Detergent and Additives” in your Instructions for Use.

1. Press

“On/Off”

to switch on the washer. The light of the selected

programme is on, and the

“Start (Pause)”

button blinks.

2. Turn the

programme selector

to the desired programme -

it is marked by a light.

3. The predefined

temperature

and

spin speed

can be altered by

pressing the “Temperature” and the “Spin speed” modifier.

Selecting any option or modifier, the indication lights up. If the

combination of programme, options or modifiers is not possible,

the indication lights switch off automatically and a signal sounds.

“Eco” button

• The duration of the wash is extended and the temperature

reduced. This saves you energy and maintains good washing results.

“Easy ironing” button

• Reduces creasing by increased water quantity and a very gentle spin.

“Rinse hold” button

• The laundry remains in the last rinse water without being spun:

this prevents creasing and colours from changing.

• This option is particularly recommended for the programme

“Synthetics” or “Delicate”.

• Particularly useful if you want to postpone spinning to a later

time, or if you want to drain only.

• Do not leave the laundry to soak in the rinse hold for too long.

Note:

The programme starts to “Rinse hold” when the “Rinse hold”

button light blinks; the

“Start (Pause)”

button light also blinks.

Terminate the “Rinse hold” option:

• Press the “Rinse hold” or the

“Start (Pause)”

button ; the

programme will terminate automatically with the final spin

cycle for the present wash programme.

• If you do not wish to spin the clothes, press and hold the

“Reset (Drain)”

button for a few seconds. The water is

drained out then, before the door can be opened.

“Spin speed” modifier

• Every programme has an automatic predefined spin speed.

• Press the button to set another spin speed.

• Spin speed “0” is only selectable for programme “Spin &

Drain”; the final spinning is cancelled in this case - the water is

drained out only at the end of the programme.

“Rinse” modifier

• “Sensitive skin”: maximum amount of rinse water is added, and

rinse cycle is prolonged.

• “Intensive rinse”: more rinse water is added, and rinse cycle is

prolonged.

• Particularly suitable for areas with very soft water, for baby

clothes or to help people with skin allergies.

CONSUMPTION DATA

Programme

Te m p e r a t u r e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approximate programme duration

(hours : minutes)

Cotton (Antibacterial) 95 11.0 95

3.38 3:10

Cotton with “Eco”

***

60 11.0 86 1.87 2:51

Cotton 60 11.0 89.2 1.92 2:15

Cotton 60 5.5 55 1.22 1:40

Cotton 60 3.5 45.5 1.03 1:25

Cotton 60 1.0 35 0.73 1:00

Coloured

***

40 10.0 86 0.90 2:36

Coloured 40 5.5 57 0.69 1:39

Coloured 40 3.5 43.3 0.58 1:27

Coloured 40 1.0 26.1 0.39 0:40

Synthetics 40 5.5 69.0 0.60 1:53

Synthetics 40 3.0 42.1 0.60 1:23

Jeans 40 11.0 117.5 0.97 2:00

Daily 40 6.0 60.9 0.81 1:00

Quick wash 30 6.0 43.8 0.44 0:30

Sport 30 5.5 61.3 0.51 1:31

Big items 40 4.0 83.7 0.83 1:18

Delicates 30 4.0 79.6 0.50 0:52

Wool 40 3.0 68.6 0.78 0:43

Handwash 30 3.0 97 0.49 0:38

SuperEco 60 11.0 95.8 1.54 5:09

Prewash cycle increases programme duration by approximately 15 min. Consumption values were measured in normalized conditions in compliance

with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure

and temperature, the load and the type of wash.

The remaining time indicator can deviate from the values in the table, because it takes into account the operating conditions at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference programme for energy label according to EN60456 and for comparative tests at test institutes.

ADD DETERGENT, CLOSE THE DOOR AND

SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION OR MODIFIER

“Options” modifier

Prewash:

• Adds a prewash cycle to the programme selected.

• Use only for heavily soiled loads (e.g. sand, granular dirt).

• Increases the cycle time by approx. 15 minutes.

• Do not use liquid detergent for the main wash when activating

“Prewash”.

Clean +

• Choose this option if you use an in-wash additive for stain

removal (powder, for example Vanish).

• Optimizes the additive's efficiency to get better wash

performance and stain removal.

• Select temperature of 30 or 40°C and use with maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the prewash chamber.

• Appropriate for use of stain removers and bleaches on oxygen

basis.

Chlorine or perborate bleaches must not be used!

Normal

“Soil level” modifier

• Adapts the programme duration to the soil level of your laundry.

If there is a programme setting which you use frequently, the

washing machine offers the possibility to save one setting for each

programme so that it can be used again by just pushing one button.

• Select the desired programme, temperature, spin speed and

options/modifiers.

Press and hold the

“Favourites”

button for some seconds; the light

goes on and a signal sounds when the programme setting is saved.

Next time you want to use your individual programme setting, turn the

programme selector to the desired programme,

shortly

push the

“Favourites”

button and start by pressing

“Start (Pause)”

If you want to replace the saved setting by another one:

• Select the programme desired and the new temperature, spin,

options/modifer setting.

•Press and hold the

“Favourites”

button for at least 3 seconds;

the previously saved setting is replaced by the new one.

The “Start delay” allows to run the machine at the consumer’s

convenience, for example at night when electricity is cheaper.

• Select programme, temperature and options/modifiers as desired.

• Press the “Start delay” button to select the delay time by 1 to 24 hours;

•Press and hold the

“Start (Pause)”

button ; the

countdown of the delay time begins. The light of the “Start

delay” button will keep blinking until the programme starts.

• The time delay indication disappears when the programme

starts and it is replaced by the remaining time.

To cancel the “Start delay”:

•Press

“Reset (Drain)”

for at least 3 seconds, or set the delay

time to “0:0” - the delay time will disappear from the display

after a few seconds.

Turn on the tap and press and hold the

“Start (Pause)”

button

- the button's light stops blinking and goes on; it will take some time

until water enters into the washing machine.

The programme sequence indicator on the display shows the

sequence reached in the programme. After starting the

programme, the indication runs from left to right through “Add

garment”, prewash, wash, rinse, spin. When a programme

sequence is finished, the corresponding symbol goes off.

The display shows the remaining programme time. Due to

variations in load and temperature of inlet water, the remaining

time is newly calculated in certain programme phases. If this is the

case, an animation appears on the display and the and the

“Dynamic Sense” symbol lights up.

As soon as a programme starts, the “Door locked” symbol lights

up on the display.

You can interrupt the programme by pressing

“Start (Pause)”

- the light blinks. The “Door locked” symbol on the display goes

off and you can open the door. In certain programme phases, the

“Door locked” symbol remains lit to show that the door cannot

be opened in the present programme phase, e.g. when the water

level is too high or during spinning.

As long as the “Add garment” symbol lights up on the display,

you can add more washing: press

“Start (Pause)”

, open the

door, add your washing, close the door and press

“Start (Pause)”

to continue the programme.

“End” appears on the display, and a signal sounds.

1. Switch the machine off by pressing

“On/Off”

2. Turn off the tap and open the door to unload your washing. Leave

the door open for some time so that the washer’s inside can dry.

1. Press the

“Start (Pause)”

button to interrupt the

programme. The light blinks.

2. Select the new programme, temperature and options/

modifiers as desired.

3. Press the

“Start (Pause)”

button again. The new

programme continues at the same position where the

previous programme was interrupted. Do not add detergent

for this programme.

Press and hold the

“Reset (Drain)”

button for a few seconds; the

light blinks. It will take some time until any existing water is drained

out and the door can be opened (up to 10 minutes). Caution, the

washing could still be hot!

SAVE YOUR FAVOURITE PROGRAMMES

START DELAY

➡

PROGRAMME START

ADD WASHING/DOOR LOCK

PROGRAMME END

CHANGE THE PROGRAMME, TEMPERATURE,

OPTIONS AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

The Sensor Technology automatically adapts programme time, water and energy consumption to the size of your wash load.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht WA 8511 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht WA 8511

Bauknecht WA 8511 User Manual - German - 3 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bauknecht WA 8511 Manual

Product: