Load your laundry, close the door properly and add detergent as
indicated on the front page and as described in the chapter “Detergent
and Additives” in your Instructions for Use.
1.Turn the programme selector to the desired programme.
The display shows the programme duration in hours and
minutes as well as the predefined temperature. The “Start
(Pause)” button blinks.
2.The temperature can be altered by pressing the
“Temperature” button.
3.The indication lamp of the predefined spin speed lights up. In
case you want to set another spin speed, press the “Spin
speed” button.
Push the button of any option desired - the respective indication
lights up.
When the combination of programme and option is not possible,
the light switches off automatically. Unsuitable combinations of
options are deselected automatically.
“Rinse hold” button
•The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent
colours from changing.
•It is particularly useful if you want to postpone spinning to a
later time, or if you want to drain only.
•If you select “Rinse hold”, do not leave the laundry to soak in
the rinse hold for too long.
•The programme stops to “Rinse hold” when the “Rinse hold”
indication in the programme sequence indication lights;
the “Start (Pause)” button blinks.
To terminate the “Rinse hold”:
•If you want to drain only without spinning: Press the “Start
(Pause)” button to start the drain process.
•If you want to spin your laundry: Press the “Spin speed” button
to select the desired spin speed and then “Start
(Pause)” to start the spin cycle.
“Prewash” button
•Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
•Recommended for heavily soiled laundry (e.g. containing sand
or granular dirt).
•Do not use liquid detergent for the main wash when activating
the Prewash option.
“Clean +” button
•Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
•Use with maximum load.
•Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
•May prolong the programme by up to 15 minutes.
•Appropriate for use of stain removers and bleaches on oxygen
basis. Chlorine or perborate bleaches must not be used!
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft
water, washing baby linen and helping people with allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and a very gentle spin.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
without “Rapid”with “Rapid”
Mixed406.0670.581:00—
Cotton957.075**2.402:20—
Cotton*607.0540.804:002:20
Cotton*603.5430.723:00
Cotton407.0690.723:002:05
Cotton*403.5460.622:45
Synthetics603.548**0.951:551:14
Synthetics403.5450.531:400:59
Delicates302.5600.400:45—
Wool/Handwash402.0490.630:40—
White407.0690.702:20—
Light colours405.5700.501:20—
Dark405.0450.501:401:15
Super Silent607.0690.844:00—
AquaEco403.0190.451:00—
Speed 15303.0300.200:15—
Jeans406.0650:551:301:15
Big Items403.0740.751:30—
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the
values in the table in relation to the water supply pressure and temperature, the load and the type of wash. Water and energy consumption refer to the default setting of
the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
*Reference programmes for Energy Label.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.
***Automatic adaptation of programme duration after detection of wash load.
***
***
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Rapid” button
•Enables quicker washing by shortening the programme duration.
•Recommendable for only lightly soiled laundry.
•Not selectable for Cotton 70 - 95°C.
“Spin speed” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If you select spin speed “0”, the final spinning is cancelled, and
the water is drained only. However, intermediate spin phases
remain during the rinse.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
•Select programme, temperature and options.
•Press the “Start delay” button to select a delay time up to 23
hours. The light of the “Start (Pause)” button blinks.
•Press the “Start (Pause)” button . The countdown of the
delay time begins. The light of the “Start (Pause)” button
is on. The light of the start delay button will keep blinking
until the programme starts.
•As soon as the programme starts, the start delay on the display
is replaced by the remaining programme time, and the light of
the “Start delay” button goes off.
•Once having pressed the “Start (Pause)” button , the
number of hours preselected can be changed by pressing and
holding the “Start delay” button.
To cancel the “Start delay”
...before you press “Start (Pause)” :
•Turn the programme selector to another position, or briefly
press the “Reset/Drain” button .
...after having pressed “Start (Pause)” :
•Press “Start (Pause)” - the delay time disappears from
the display. Press “Start (Pause)” again to start the
selected programme immediately.
Open the tap and press “Start (Pause)” . The light stops
blinking and is on. The programme sequence indicator shows the
current programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is the
case, an animation appears on the display.
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
•Turn the programme selector to a programme position, or run
a programme as usual.
•Press the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds. A key-like symbol will shortly
appear on the display to indicate that the child lock is active.
Any time you try to change a programme setting with active child
lock, the display will briefly show the key-like symbol. The
programme setting cannot be changed anymore. The only change
possible is to switch the washer off by turning the programme
selector to the “Off/O” position. To deactivate the child lock:
•Press again the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds.
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one button.
•Select the desired programme, temperature, spin speed and
option(s), push and hold the “Favourites” button for at
least 3 seconds. The “Favourites” indication briefly blinks
and then lights up - the programme setting is saved.
Next time you want to use your individual programme setting,
select the the programme, briefly push the “Favourites” button
and start by pushing “Start (Pause)” .
If you want to replace the saved programme setting by another
one, proceed as already described above.
Before starting and after end of a programme, the lamp lights to show
that the door can be opened. As long as a wash programme is running,
the door remains locked and must on no account be forced open. In
case you have an urgent need to open it during a running programme,
refer to “Reset a running programme before the end”.
If one of the failure indications lights up, refer to the
“Troubleshooting Guide” in your “Instructions for Use”.
In case you used too much detergent, a small vertical bar will light
next to the overdosage symbol on the right of the display when
the wash programme is finished; use less detergent next time. Too
much foam by detergent overdosing can also lead to interruption
of a wash cycle; in this case the display shows “Fod” - follow the
recommendations in the “Troubleshooting Guide” in your
Instructions for Use to solve the problem.
•The display shows “End” and the “Door open” indication lights.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
4.Leave the door ajar to allow the drum to dry.
1.Press “Start (Pause)” to pause the programme. The
light blinks.
2.Select the new programme, temperature, any options and
another spin speed if you want.
3.Press “Start (Pause)” again. The light is on, and the
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The “Reset/Drain” button cancels a programme before
the end.
•Press the “Reset/Drain” button for at least 3
seconds. “rES” appears on the display. The water is drained
out; it may last a while until you can open the door.
START DELAY
PROGRAMME START
CHILD LOCK
SAVE YOUR FAVOURITE PROGRAMMES
“DOOR OPEN” INDICATION
FAILURE INDICATIONS
DETERGENT OVERDOSAGE INDICATION
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
40105575GB.fm Page 2 Friday, May 27, 2011 11:50 AM
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bauknecht Prestige 4470 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bauknecht Prestige 4470 in the language / languages: English as an attachment in your email.
The manual is 1,56 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
