(siehe rechte Seite zur Beschreibung der Zusatzfunktionen)
PROGRAMMWAHLTASTE
Die Taste „P“ (mehrfach)
drücken, bis die gewünschte
Programmnummer (P1...Px) auf
dem Display angezeigt wird (siehe
unten „Programmübersicht“).
TASTE START/FORTFAHREN
Drücken Sie diese Taste, um das gewählte Programm zu
starten: Die Anzeigelampe leuchtet auf und erlischt bei
Programmende.
Wird die Tür während des Spülgangs geöffnet, wird der
Programmablauf vorübergehend unterbrochen: die
Start-Kontrolllampe blinkt. Zum Neustart die Tür
schließen und erneut die Start-Taste drücken.
TASTE ABBRUCH/AUS
Diese Taste drücken, um die Bedienblende
abzuschalten.
Wird die Taste während des Programmablaufs gedrückt,
wird das laufende Abpumpprogramm 1 Minute lang
angehalten (auf dem Display wird 0:01 angezeigt).
Wird die Taste bei abgeschaltetem Gerät gedrückt, wird
das gesamte Restwasser (1 Minute lang) abgepumpt.
1)Die Programmdaten sind Labormesswerte gemäß Norm EN 50242, bei normalen Bedingungen (ohne Zusatzfunktionen). Sie können sich abhängig von den Bedingungen ändern. Bei
Sensorprogrammen können die Unterschiede durch die gelegentliche automatische Kalibrierung des Systems bis zu 20 Minuten betragen.
2)Energie-Label Programm gemäß EN 50242. - Hinweis für Prüfinstitute: Wenden Sie sich bitte bezüglich detaillierter Informationen über die Bedingungen der EN-Vergleichsprüfung und
abweichender Prüfungen an folgende Adresse: „nk_customer@whirlpool.com“.
3)Die antibakterielle Wirkung wurde auf der Grundlage der Norm NF EN 13697 vom November 2001 vom Institut Pasteur in Lille/Frankreich getestet.
Programmübersicht
Reiniger
Verbrauch
Trocken-
Phase
Programme
Verfügbare
Zusatzfunktionen
Beladungsempfehlungen
LiterkWh
Minuten
1)
P1
Sensor40-70 °C
Startvorwahl
Halbe
Beladung
Für den täglichen Gebrauch, mit
leicht angetrockneten Speiseresten
(z. B. EN 50242)
X7-141,00-1,6580-165Voll
P2
Pre-Washkalt
Startvorwahl
Geschirr, das später gespült werden
soll.
—4,00,0314NEIN
P3
Glass40 °C
Startvorwahl
Leichte Verschmutzung, zum Beispiel
Gläser und Tassen.
X10,00,85100Kurz
P4
Express45 °C
Startvorwahl
Leicht verschmutztes Geschirr ohne
angetrocknete Speisereste.
X11,00,8030NEIN
P5
Eco
2)
50 °C
Startvorwahl
Halbe
Beladung
Normal verschmutztes Geschirr.
Energiesparprogramm.
X11,01,03185Voll
P6
Normal60 °C
Startvorwahl
Halbe
Beladung
Normal verschmutztes Geschirr. X10,01,3080Voll
P7
Intensive65 °C
Startvorwahl
Stark verschmutztes Geschirr,
besonders Töpfe und Pfannen.
X14,01,60145Voll
P8
Hygiene
3)
Startvorwahl
Normal oder stark verschmutztes
Geschirr, mit zusätzlichem
antibakteriellem Spülprogramm. Eine
Unterbrechung des Programms
(z. B. durch Öffnen der Tür) kann die
keimtötende Wirkung beeinträchtigen.
X13,01,50118Voll
5019 496 01767
BITTE LESEN SIE DIESE KURZANLEITUNG UND DIE MONTAGEANWEISUNGEN
VOR DEM ERSTEN GEBRAUCH DES GERÄTS SORGFÄLTIG DURCH!
Zusatzfunktionen und Display – Beschreibung
SALZANZEIGE
Wenn sie (nach Programmablauf)
aufleuchtet, muss Spezialsalz
nachgefüllt werden.
KLARSPÜLERANZEIGE
Wenn sie (nach Programmablauf)
aufleuchtet, muss der
Klarspülerspender aufgefüllt
werden.
SPÜLZEITANZEIGE
Zeigt die Programmdauer und die Restzeit an (h:min). Mit der ausgewählten „Startvorwahl“ wird die Restzeit bis
zum Programmstart angezeigt (h.00) – unter 1 h (0:min).
Wird die Anzeige „Fx Ey“ eingeblendet, siehe Seite 6 – Kapitel „Was tun, wenn...“.
DIE BEDIENBLENDE DES GESCHIRRSPÜLERS WIRD DURCH DRÜCKEN EINER
BELIEBIGEN TASTE (AUSSER DER ABBRUCH-/AUS-TASTE) EINGESCHALTET.
ZUR ENERGIEEINSPARUNG SCHALTET SICH DIE BEDIENBLENDE AUTOMATISCH
AB, WENN INNERHALB VON 30 SEKUNDEN KEIN PROGRAMM GESTARTET WIRD.
Dear Forum, I have a problem with my dishwasher I have the errors F6 and E4 coming out. The dishwasher starts but then the error message
Submitted on 8-3-2019 at 15:23
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bauknecht GSU 5545 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bauknecht GSU 5545 in the language / languages: German as an attachment in your email.
The manual is 3,18 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.