installation and maintenance instructions carefully!
1)Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra functions,
sensor settings (only with sensor programmes), water supply temperatures, water hardness and power supply voltage.
2)Energy label programme in compliance with EN 50242. - Information for Test Laboratories:
for more detailed information on the EN comparison test and
other tests, contact the following address: “nk_customer@whirlpool.com”.
3)The antibacterial action has been shown in collaboration with the Pasteur Institute, Lille (France), in conformity with. Standard NF EN 13697 - November 2001.
1. OVERVIEW
Programme selector
START button
The indicator lights up during operation, flashes when a fault
occurs, and goes off at the end of the programme.
START button RESET function:
Press this button for at least 2 seconds; the selected programme
and options are cancelled. Main failure displays (repeated flashing
of the START indicator lamp) can be cancelled by RESETTING.
Detailed instructions are given in chapter 5 “What to do, in the
event of...”.
Rinse aid level indicator and salt level indicator
They light up when rinse aid or salt need to be added.
Add just before starting a wash cycle.
Fault indication and wash time display
In normal operation it indicates the remaining time (h:mm),
whereas with “Delayed start” selected it indicates the time
remaining until programme start (hh).
If “F..” appears on the display, see chapter 5 “What to do, in the
event of.
“Delayed start” button
Press the button (repeatedly) to delay the start of the programme.
Adjustable from 1 to 24 hours. With each press of the button, the
delayed start indicator increases by one hour and after 24 restarts
from 00. Then press the START button. The dishwasher will start
after the set time.
Detergent setting upon initial use and when using a different type of detergent
1.Select the third programme in the relative table.
2.Press the START button for approx. 7 sec. to change the display.
3.Using the START button, select the desired detergent:
Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action
detergents (in this way, the rinse aid and/or salt indicator is deactivated).
Display shows OFF = Powder detergent (factory setting).
(rinse aid level and salt level indicator activated).
4.Switch the appliance off and then switch it on again. The selected detergent
type will be indicated on the display for approx. 3 seconds .
Half Load/Multizone button
Load the upper or lower rackonly.
Press once = wash upper rack (the indicator/symbol lights up)
Press twice = wash lower rack (the indicator/symbol lights up)
Press 3 times = Off (Half load/Multizone deactivated).
When washing without the upper rack, press the “Half load” (i.e.
“wash lower rack”) button twice (the corresponding indicator/
symbol lights up).
Power Clean
An additional spray level offers better cleaning result and more
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bauknecht GSIP 40 POWER IN at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bauknecht GSIP 40 POWER IN in the language / languages: English as an attachment in your email.
The manual is 0,26 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
