806823

Bauknecht CTAR 7642 IN Manual

5
Zoom out
Zoom in
Previous page
1/7
Next page
CONTROL PANEL
DAILY USE
SWITCHING THE HOB ON/OFF
To switch the hob on, keep button “A“ pressed for approx. 2 seconds.
The 4 cooking zone displays show “0“. If within 20 seconds none of the
cooking zones is activated, the hob switches o automatically as a safety
precaution.
SWITCHING ON AND ADJUSTING COOKING ZONES
Press one of the buttons “B“ corresponding to the cooking zone you
intend to use. Select the heat setting required with buttons “E“ or “C“.
The other selectable cooking settings go from 1 to 9. Press buttons “+/−“
at the same time to cancel all settings.
IMPORTANT: the control is deactivated 10 seconds after the heat setting has
been selected.
To change the heat setting, rst press the selection button “B“ again, then
proceed to change the setting, using buttons “E“ or “C“.
MULTIPLE ZONE
After selecting the desired zone and setting the level (as described in
the previous section) press “F“: an indicator above the button turns
on,activating the additional zone.
The multiple zone can only be used if:
• The cooking zone is provided with multiple zone;
• The power level selected is greater than 0.
To deactivate the multiple zone, press button “B“ of the desired zone,
then press “F“ again.
TIMER
To set the Timer function, select the desired cooking zone and power
setting then press the cooking zone key again and a luminous dot
will appear on the display of the timer-controlled cooking zone. The
indication “00“ blinks on the 2 displays. Press buttons “C“ or “E“ to set
the time from 1 to 99.
IMPORTANT: after 10 seconds the timer displays will show the power
setting of the other cooking zones.
To view the remaining cooking time, press the timer-controlled cooking
zone key twice.
A FUNCTION
This function allows to automatically decrease the cooking zone power
level from the highest value (level 9) to the one selected by the user for
a later stage of cooking.
To activate this function rst press the “+“ button when level 9 is reached.
The display shows “A“ and “9“ ashes alternately with low brightness.
At this point, choose the desired power level (less than 9) with the “–“
button.
“A“ and selected level ash alternately with low brightness on the display.
The function is activated once “A“ and the selected level ash alternately
with high brightness on the display.
Once “A“ is no longer visible on the display (the “A“ function switches o
automatically after several minutes, depending on the set power level),
the cooking process continues with lower power and the display shows
only the selected power level.
N.B.: this function is not possible with level 9.
KEY LOCK
The Key lock function is switched on by holding down button “D“ until
a dot lights up above the function button. The control panel is locked
except for the switching-o function. The function remains on even after
the hob is switched o and on again and can be deactivated by pressing
button “D“ again until the dot above the function button goes o.
When the hob is o with the key lock activated to switch the hob on, rst
deactivate the key lock function by pressing button “D“ again until the
dot above the function button goes o.
The presence of water, liquid spilled from pots or any objects resting on
the controls can accidentally activate or deactivate the Key lock function.
RESIDUAL HEAT INDICATOR
When the cooking zone is switched o, the residual heat indicator “H“
remains on or ashes alternating with “0“ until the temperature of the
hob returns within safety levels.
IMPORTANT: The hob’s safety features include an automatic switching
o function. Prolonged use of the same heat setting triggers automatic
switch-o of the cooking zone (for example, after around 1 hour at
maximum heat setting, the cooking zone switches o).
IMPORTANT: To avoid a permanent damage the hob:
• do not use pots with bottoms that are not at;
• do not use metal pots with enamelled bottom;
• do not place hot pots/pans over the control panel.
FIRST TIME USE
Upon rst installation, the control panel performs a functional test for about
1 second, after which it automatically switches to the “Key lock” function.
To deactivate the function, press and hold button “D”; an acoustic signal
will sound and the corresponding led will turn o.
NOTE: If a reset occurs, repeat the procedure described above.
F
B
E
C D
A
AOn/O
BCooking zone and timer selection
C-E Heat setting increase and decrease
DKey lock
FMultiple zone Activation / Deactivation
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht CTAR 7642 IN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht CTAR 7642 IN in the language / languages: English as an attachment in your email.

The manual is 0.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht CTAR 7642 IN

Bauknecht CTAR 7642 IN User Manual - German - 7 pages

Bauknecht CTAR 7642 IN User Manual - Dutch - 7 pages

Bauknecht CTAR 7642 IN User Manual - French - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info