Manual Batavia 909 TOUCH PRO 3113-210 (page 43 of 48) (English, German, Dutch, French)

589463

Zoom out

Zoom in

1/48

Original Instructions

sunlight or any other heat source.

• DO NOT force cool the pack in any way. Do not place in refrigerators

or freezers. When the battery pack has cooled down it can again

be used to operate the drill, as long as the load or the conditions

causing the original excessive temperature has been corrected.

Low voltage cut out

This tool is fitted with a low voltage cut out feature to assist in providing

a long life to the battery.

When the battery is close to the pre-set minimum low voltage level, the

power consumption LED will be red and the tool will turn off. You will

then need to insert either a fully charged battery pack into the drill or

recharge the existing battery pack.

Note: Attempting to restart the tool without either recharging the battery

or installing another battery (with charge) will lead to drill restarting and

then stopping again, after only a few seconds of operation.

Drilling

DRILLING METALS

• Always clamp sheet metal.

• Support thin metal with a block of wood to avoid distorting it.

• Use a punch to mark the centre of the hole.

• Use a suitable lubricant for the material you are working on.

USE / FOR:

Oil / Steel

Turpentine or paraffin / Aluminium

Do not lubricate brass, copper or cast iron

DRILLING MASONRY

• This drill is not designed for drilling masonry. Purchase or rent a

hammer drill.

DRILLING WOOD

• Clamp a piece of scrap wood to the back of your work to prevent

splintering.

ALL DRILLING OPERATIONS

• Mark off the centre of the hole using a centre punch or nail.

• Don’t force the drill, let it work at its own pace.

• Keep the drill bit sharp.

• Reduce pressure as the drill is about to break through the item

being drilled.

WARNING! Be prepared for binding when the bit break

through the workpiece, because the drill has a tendency to grab

and kick opposite to the direction of rotation, which could cause a

loss of control. If the operator is not prepared, this loss of control

could result in serious injury.

MAINTENANCE

CAUTION!

Always disconnect the device before performing any adjustment

or maintenance operation. If the supply cord is damaged, it must

be replaced by the manufacturer or its service agent in order to

avoid a hazard.

Disconnect from the power supply immediately if the supply cord

is damaged.

Take care not to expose this tool to the rain.

CLEANING

Avoid using solvents when cleaning plastic parts. Most plastic parts are

susceptible to damage from various types of commercial solvents and

may be damaged by their use. Use clean cloths to remove dirt, carbon

dust, etc.

STORING

Store the machine, operating instructions and where necessary the

accessories in the original packaging. In this way you will always have

all the information and parts ready to hand. Pack the device well or use

the original packaging in order to avoid transit damage. Always keep the

machine in dry place.

For Lithium-ion battery pack storage longer than 30 days:

• Store the Lithium-ion battery pack where the temperature Is below

26°C and free of moisture.

• Store Lithium-ion battery packs in a 30%-50% charged condition.

• Every six months of storage, fully charge the Lithium-ion battery

pack.

• Exterior may be cleaned with a cloth or soft non-metallic brush.

DISPOSAL

Do not dispose of power tools into household waste! According the

European Guideline 2012/19/EU for Waste Electrical and Electronic

Equipment and its implementation into national right, power tools that

are no longer usable must be collected separately and disposed of in an

environmentally correct manner.

Touch_MA_multi_1404-30.indd 43 01-05-14 15:33

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia 909 TOUCH PRO 3113-210 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia 909 TOUCH PRO 3113-210 Manual

Product: