Manual Basetech 1529040 (page 4 of 6) (English, German, Dutch)

738539

Zoom out

Zoom in

1/6

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in

electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

• Never touch a time switch that shows signs of damage, as this could cause a fatal

electric shock!

First, switch off the mains voltage to the socket to which the time switch is con-

nected (switch off at the corresponding circuit breaker or remove the safety fuse

or switch off at the corresponding RCD protective switch, so that the socket is fully

disconnected).

Only then can you remove the time switch from the mains socket. Do not use the

damaged time switch any longer and dispose of it in an environmentally-friendly

manner.

Preparation

Type plates in different languages are included in the package. Stick the language plates in

your language over the German language label on the back of the time switch.

Initial operation

Plug the time switch (without any device plugged in!) into a suitable mains socket (with a

protective earth conductor).

If the time switched is used outdoors, plug it only into an IP44 wall outlet with earth contact.

You must only use it in the position described below. The socket must be on top, the wheel for

setting the time at the bottom. Both covers must open upwards.

Top

Bottom

Setting the time

Lift the transparent cover with one hand. Turn the outer ring with the hours printed on it clock-

wise with the other hand until the arrow “ ” on the inner ring shows the current time. Close

the cover.

Turn the setting ring only clockwise to the right; it is easy to move.

It is not possible to turn it anti-clockwise! Do not exert any force! If the time switch is

damaged due to that, the warranty will be void!

The time switch only works when it is supplied with electricity, i.e. when it is connected to an

active mains socket.

Setting the on/off times

You can set the times for switching the connected device on and off with the 48 segments

(2 per hour) in a 30-minutes raster. A segment pressed down activates the socket (voltage on,

connected device on), a segment pushed upwards or pulled out switches the socket off (no

voltage, the connected device is off).

Example: If you wish a lamp to be switched on between 22:00 and 23:00, press the two seg-

ments between 22:00 and 23:00 downwards. All the other segments must be pulled out.

Due to the design of the time switch (mechanical operation and switch process; 48

shift segments for 24 hours), deviations from the switching times will occur.

For switching processes or switching times that require accuracy, electronic timer

switches should be used instead.

However, the mechanical time switch has the great advantage that a setting can be

made very quickly.

Connecting a device to the time switch

• Switch the device off.

• Flip the cover of the time switch outlet open and hold the cover with one hand.

• Plug the device into the time switch outlet; push the plug fully into the outlet of the time switch.

• Slowly close the cover of the time switch (do not let it ip shut).

• Switch the device on.

Care and cleaning

Before cleaning the product, disconnect the appliance from the time switch. Disconnect then

the time switch from the power supply by pulling it out of the mains socket.

Never use abrasive cleaning agents, rubbing alcohol or other chemical solutions, since these

could damage the housing or even impair operation.

Use a dry, lint-free cloth to clean the product.

Disposal

Electronic devices are recyclable material and do not belong in the household

waste. Dispose of an unserviceable product in accordance with the relevant statu-

tory regulations.

Technical data

Operating voltage .................................230 V/AC, 50 Hz

Connection power .................................Resistive load: max. 3680 W (230 V/AC, 16 A)

..............................................................Inductive load: max. 460 W (230 V/AC, 2 A)

Devices with mainly resistive load are, e.g., light bulbs, heaters, etc.

Powered devices with inductive load are, e.g., motors, control gears, conventional

transformers, energy-saving bulbs, etc.

Protection class ....................................I

Protection type ......................................IP44

Switch type ...........................................Micro-switch (single-pole)

Smallest switchable time unit ...............30 min (48 switch segments for 24 hours)

Socket with child protection ..................yes

Operating conditions .............................Temperature -20 °C to +40 °C

Dimensions ........................................... 130 x 60 x 95 mm (L x W x H, including plug)

Weight ..................................................156 g

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Basetech 1529040 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Basetech 1529040 Manual

Product: