765280
25
Zoom out
Zoom in
Previous page
1/27
Next page
T e c h 3 0 0 User Guide R.59.1 2020
25 | P a g e
The TECH300 tool has the ability to perform the necessary mode change. If a sensor is shown
as Ship”, “Test” or “Off” and the relearn toolkit provides the option “Set Sensor to Park Mode”,
please use this option to change the sensor mode into the correct one:
Go to “Relearn” and select vehicle (MMY).
Press enter when relearn procedure shows.
Select the spanner in the upper left corner with the Up/Down buttons. Press Enter.
Select “Set Sensor to Park Mode”, press Enter.
Go to the wheel, hold the tool near the sensor and press “Test”.
Repeat for each wheel.
Start the Relearn procedure.
Also, some sensors are supplied in a mode where they cannot be read by the tool unless they
are pressurized in a wheel. Some examples would be replacement sensors bought from a Ford
dealership, and some Mitsubishi Continental sensors.
APPENDIX D: COMMS ERROR TROUBLESHOOTING
If a problem or error occurs during the COMMS process, follow the steps below before calling
customer support.
Check vehicle ignition
Vehicle ignition must be in the RUN position in order for vehicle COMMS process to complete.
Check cable to tool connection
Insure the cable is connected at the DB15 and thumb screws are finger tight.
Check cable connection at vehicle
Make sure OBDII connection is good.
Verify Make, Model, and Year
COMMS can change from Model to Model, and Year to Year. Verify the tool is set-up to the
proper MMY.
Verify tool power level
If the tool has a low battery charge, this may affect the COMMS process. Charge tool and try
again.
TECHNICAL SPECIFICATION
Power Supply
Lithium Polymer rechargeable battery, not user serviceable
Max power consumption
1.5W Schrader TPM, 0.5W all others
Display
LCD single colour, graphic, resolution 128x64
Keyboard
7 keys, dust, water and grease-resistant
Input/output
Mini-B style USB used to Connect to PC for firmware
update and audit file download.
Vehicle connection
15 way D connector on tool connects cable with OBDII
connector (optional) on the other end
Working environment
Temperature 0°C - 45°C, Humidity: 20-55%
Storage environment
Temperature 10°C - 50°C, Humidity: 20-60%
Dimensions
187mm x 107mm x 47mm
Weight(including batteries)
410g
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bartec Tech 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bartec Tech 300 in the language / languages: English as an attachment in your email.

The manual is 1,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bartec Tech 300

Bartec Tech 300 User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info