474147
3
Zoom out
Zoom in
Previous page
1/25
Next page
Safety precautions
The vehicle electric system must have 12VDC voltage with negative to ground. Make sure your car has it in order to
avoid any damages to your amplifier and to the car itself.
Suitably fix the amplifier paying utmost attention if you install it into the driver’s compartment. Use extra fixing systems
if you install it inside the bonnet. If the amplifier detaches itself while you are driving, it can severely damage people and
other vehicles.
Power supply cable must have mechanically resistant and self-extinguishing insulation. Its section has to comply with
what is indicated in this manual. When placing it, avoid to press it against cutting parts or close to mechanical moving
objects. Make sure it is suitably fixed all along its length. Block positive and negative cables just close to the amplifier
respective power supply terminal blocks through a clamping screw.
Put a fuse holder close to the battery positive terminal; connect one end of the power supply cable to it after
connecting its other end to the amplifier. The fuse value must be 50% higher than the amplifier built-in one. In case
the cable supplies several amplifiers, the fuse value will have to be 50% higher than the sum of the values of all other
fuses in the system.
For safer driving, we recommend to adjust volume not to drown external traffic sounds.
WARNING. When the amplifier works in particularly hard conditions, it can reach 90°C (194°F). Make sure its
temperature is safe before touching it.
Functioning precautions
Install the amplifier in locations where temperature is between 0°C (32°F) and 55°C (131°F).
There must be suitable air circulation where you install the amplifier; this area must not be affected by humidity, rain,
external deposits or parts coming from the vehicle mechanical devices. Let the amplifier glass upper part (i.e. the part
where air goes in and out) be at least 10 cm (4”) far from possible walls.
When installing speakers and the cables that connect them, make sure that non-insulated parts never touch the car
cutting parts. If they do, the amplifier protection intervenes.
Listening level calibration is made by adjusting the source volume up to 3/4 of its maximum level; then, adjust the
amplifier levels until you can hear distortion and you can see PEAK indicators are occasionally on.
Avoid to start the car engine with the amplifier on. If the battery isn’t sufficiently charged, in case you start the car with
the audio system on, the amplifier could go in the protection mode.
In this case isn’t sufficient to shut off the audio system and turn it on after some seconds.
Maintenance and reliability precautions
Periodically clean the amplifier avoiding to use aggressive solvents that might damage it. Dampen a piece of cloth with
water and soap, wring it and clean the amplifier with it. Then, clean the amplifier by using a piece of cloth dampened with
water only; eventually clean it with a dry piece of cloth.
Remove dust and solid deposits from the five upper grilles through which air goes in and out. This must be periodically
done by removing the magnetic fixing grilles and by cleaning the filter you can find underneath them as indicated in
this manual. Avoid to use compressed air on the grilles without removing them, since it would push solid parts into the
amplifier. If necessary, please contact a specialised service centre for internal cleaning. Air ducts obstruction makes the
amplifier go in safety.
- 2 -
GENERAL RECOMMENDATIONS
INTRODUCTION
1
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audison Thesis HV Venti at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audison Thesis HV Venti in the language / languages: English as an attachment in your email.

The manual is 9,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info