583736

Audiovox AA-RS30CS Manual

2
Zoom out
Zoom in
Previous page
1/20
Next page
The AA-RS30CS is Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles
Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may
be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a instant fire, (no glow plug
pre-heat system), feature #9 should remain in the default Gasoline mode setting. For diesel applications, consult your
dealer for the type of ignition system used in your particular vehicle. Regardless of the vehicle, Gasoline or Diesel, for
every installation, the vehicle MUST HAVE a Tach Signal Input, and an Automatic Transmission.
INSTALLATION OF THE MAJOR COMPONENTS:
CONTROL MODULE:
Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location
selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness.
Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting the module
to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around or block the
steering wheel preventing proper control of the vehicle. Secure the module in the chosen location using cable ties or
screws as necessary.
Do Not Mount The Module In The Engine Compartment, as it is not waterproof.
HOOD PIN SWITCH:
The pin switch included in this package is required for the safety shut down of the remote start unit. If the vehicle is
being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This
switch MUST be installed in all applications Failure to do so may result in personal injury or property damage. Mount
the switch in an area under the hood that is away from water drain paths. If necessary, the included brackets may be
used to move the switch away from rain gutters or allow mounting to the firewall behind the hood seal. In either case
the switch must be set up to allow the hood door to depress the switch at least 1/4 inch when the hood is closed and fully
extended when the hood is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully check behind the
chosen location to insure the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired
location and thread the pin switch into it using a 7/16" nut driver or deep well socket. If using the mounting bracket, first
secure the bracket to the desired location and secure the pin switch in the pre-threaded mounting bracket hole.
THE RECEIVER/ANTENNA ASSEMBLY:
The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash board
for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.
Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window
glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear window location for
best reception. Secure the antenna with double stick tape provided. After securing the antenna, we advise also
securing a section of the antenna cable to a fixed support. This will prevent the antenna from dropping down in case
the double stick tape is exposed to extreme heat which may loosen it's gummed surface.
PROGRAM SWITCH :
Select a mounting location that is within reach of the ignition switch, as this switch, in combination with the ignition
switch, will be used to program the selectable features of the system. It is suggested that the switch be mounted to the
lower dash panel in the driver's area. Inspect behind the chosen location to insure that adequate clearance is allowed
for the body of the switch, and also that the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4"
hole in the desired location and mount the switch by passing it through the panel from the underside. Secure the
switch using the nut, star washer, and on/off face plate. It is best to orientate the switch to allow the on position to be
up toward the driver and the off position to be down or away from the driver. Route the switch wires toward the control
module.
CONTROL SWITCH:
Select a mounting location known and accessible to the operator of the vehicle. A lower dash panel, kick panel, or
glove box is desirable. Inspect behind the chosen location to insure that adequate clearance is allowed for the body
of the switch and also that the drill will not penetrate any existing factory wiring or fluid lines.
2
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiovox AA-RS30CS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiovox AA-RS30CS in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info