603152

Audiophony TT-2930 Manual

7
Zoom out
Zoom in
Previous page
1/8
Next page
Page 7
TT-2930 - High-torque Professinal turntable system English
6 - Operating
1 - Turn the power dial to turn on and the speed indicator
and the strobe-illuminator will light up.
2 - Turn on and raise the target light for illumination the
stylus tip by pushing the target light button.
3 - Place a record on the turntable mat. When playing a
45rpm record with a large center hole; place the 45-rpm
adapter on the center spindle.
4 - Set the rotation speed (33/45/78) to match the record.
5 - Release the arm clamp.
6 - Set the cueing lever to the up position.
7 - Press the Start/Stop button and the turntable platter
will start to rotate.
8 - Move the tone arm over the desired groove.
9 - Set the cueing lever to the down position, the tone arm
will descend slowly onto. The record and play begins.
10 - Set the desired pitch adjusts range by depressing
the Quartz buttons until the desired pitch is reached.
Options are +/-10% or +/-20%
11 - Adjust the pitch to a desirable speed. During play,
observe the strobe dots. If the strobe dots appear to the
right, the pitch is slower than the rated speed. If they flow
to the left, the pitch is faster than the rated speed.
If the strobe dots appear stationary, which means the
platter is in normal turntable speed, move the pitch
control slider up or down to adjust the speed.
12 - To suspend play, lift tone arm with cueing lever.
13 - When play is finished, raise the cueing lever, move
the tone arm to the armrest and secure the tone arm with
the arm clamp.
14 - Turn the target light off by pushing the light back
down.
15 - Press the Start/Stop button to stop the platter
rotating.
16 - Turn the power dial to turn off the power.
1 - Remove the main unit with the packing from the box
and take off the packing.
2 - Set the 45rpm adaptor on the main unit.
3 - Insert the turntable platter onto the centre spindle.
4 - Set the slip mat on the platter.
5 - Installation of cartridge:
When installing a cartridge, refer to the operating
instructions of that cartridge. During installation, attach
the stylus protector to guard the stylus tip from damage.
(a) Connect the lead wires to the cartridge terminals. The
terminals of cartridge are colour coded.
Connect each lead wire to the terminal of the same
colour.
White (L+) Left channel +
Blue (L -) Left channel –
Red (R+) Right channel +
Green (R-) Right channel –
(b) Install the cartridge to the headshell and tighten it
with screws provided with the cartridge.
6 - Insert the headshell into the front end of the tonearm,
then turn the lock nut clockwise with the headshell firmly
held horizontally.
7 - Slide counterweight onto tonearm.
Twist it lightly and it will screw onto the rear shaft of the
tonearm.
5 - Assembly
8 - Adjustment of horizontal zero (0) balance and stylus
pressure:
(a) Remove the stylus protector, do not touch the stylus
tip during the adjustment.
(b) Set the cueing lever to the lower position.
(c) Release the arm clamp and lift the tonearm from the
arm rest to free it.
(d) Rotate the counterweight until the tonearm is
approximately balanced horizontally (floats freely).
(e) Refasten the tonearm with the arm clamp.
(f) Hold the counterweight stationary with one hand and
rotate only the stylus-pressure ring to bring the number
"0" of the ring into alignment with the centre line on the
tonearm rear shaft.
(g) Rotate the counterweight clockwise until the scale
shows the value corresponding to the pressure of the
used stylus. The stylus pressure of the installed pick-up
system is 2 g. If you use a separate pick-up system,
please follow the manufacturer’s instructions.
9 - Set the anti-skating control knob to the same value as
the stylus pressure.
10 - Install the dust cover to the main unit
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiophony TT-2930 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiophony TT-2930 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info