625601
4
Zoom out
Zoom in
Previous page
1/16
Next page
4
Rear Panel Connectors and Controls
Front Panel Controls
a) Input Select
Choose one line input channel (1 to 6) to send to each zone
output (1 to 4).
b) Zone Volume
Set the volume level for each zone (1 to 4). Turn clockwise to
increase volume, anticlockwise to decrease.
c) Mic Volume
Four screwdriver controls set the volume level from the paging
microphone mixed with each zones music signal (zones 1 to 4).
When set to zero, music ducking (see Appendix 1) is disabled
for that zone.
d) Zone signal indicator
This white indicator LED illuminates when a signal is present.
The brightness of the LED gives some indication of the signal
level.
e) Power On/O
This is a true mechanical power switch (not a standby mode).
Its position is retained even during mains power failure.
f) Power on indicator
This blue indicator LED is o when the power switch is o and
lights blue when the mains power is on. Rapid ashing
indicates that the RS-232 enabled standby mode is in
operation.
a) Mains power input
IEC 3-pin connector. Use power cord supplied.
WARNING – The power cord must be connected to a power
socket outlet with a protective earth connection.
b) Line Inputs
Six line input channels on RCA phono pairs, each of which can
accept a mono or stereo source (stereo sources are internally
mixed down to mono). The front panel Input Select switches
(see above) pick which channel is to be sent to each Zone
output.
c) Line input gain controls
Rotary potentiometer to set gain for input channels 1, 2, 3, 4, 5
and 6.
d) Input level set aid
A single 2-colour LED is provided to assist setting the line input
levels. By applying a signal on each input in turn the level can
be set optimally. Green indicates the signal is in the optimum
range (>-20dB) and Red indicates that clipping is imminent
(>-2dB)
e) Zone Outputs (unbalanced)
Four mono RCA phono sockets carry the Zone (Line) outputs.
Each Zone Output can be selected to have a at frequency
response or the Audica speaker EQ (AEQ) equalisation (see
page 6 ).
f) Zone Outputs (balanced)
Balanced audio outputs are provided on 3-way Phoenix
connectors for Zones 1, 2, 3 and 4. These replicate RCA jack
outputs for each zone. The balanced output level is double the
unbalanced output.
If taking a single-ended output from the balanced output
terminals then use the ground pin for screen and ‘+’ pin for
signal. DO NOT connect the ‘–‘ output pin to ground.
b d f ec b dc b dc b dc
a
a
db e
c
f
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audica Multizone at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audica Multizone in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info