810556
5
Zoom out
Zoom in
Previous page
1/8
Next page
5
7 PRINCIPLE OF ACTIVITY
The heat exchanger is connected to a heating water source (eg a gas hot water boiler) and the
DHW is controlled by the thermostat. By appropriate connection with the three-way distributor
valve and the pump, the DHW automatically heats and prefers heating. To achieve the required
DHW temperature set on the heater thermostat, the heating water temperature must be min. o
5 ° C higher (recommended higher by 15 ° C). The heater works on the pressure principle. There
is constant water pressure in the vessel from the water system, which allows DHW to be taken at
any distance from the heater. It is recommended to use a circulatory system for long periods of
time.
8 CONNECTING THE DHW HEATING SCHEME
Cold water is connected to an entry marked with a blue circle or "DHW INPUT". The safety valve
is mounted in accordance with the enclosed instructions. The dripping water is drained into the
drain pipe or a small expansion vessel is fitted between the container and the relief valve to
compensate for the increase in the volume of water during heating. The hot water is connected
to the outlet indicated by the red ring or the "OUTPUT".
If the DHW distribution is equipped with a circulating circuit, it is connected to the terminal
marked "CIRCULATION".
The tank has a drain output. If the pressure in the supply line is higher than 0.63 MPa, the
reducer valve must be inserted in front of the safety valve.
Each separately sealed container must be fitted with a cap and a non-return valve in the cold
water inlet.
CAUTION: There must be no stop valves between the cylinder and the safety valve!
9 CONNECTING TANK INTO THE HEATER CIRCUIT
The container is placed on the ground near or close to the heating source. Using three
adjustable screws, it aligns to a stable position. The heating circuit is connected to the indicated
inlet and outlet of the tank exchanger and the vent valve is installed in the highest position. To
protect the pumps, the 3-way valve, the non-return valves and the exchanger from the
exchanger, it is necessary to install a filter in the circuit. It is recommended to flush the heating
circuit before installation. All power supplies must be insulated sufficiently. If the system will
operate with DHW preheating using a three-way valve, always follow the installation instructions
of the three-way valve manufacturer.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATTACK Z100 PLus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATTACK Z100 PLus in the language / languages: English as an attachment in your email.

The manual is 1.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info