Manual ATAG ws9011em (page 12 of 13) (English, German, Dutch, French)

99194

Zoom out

Zoom in

1/13

- 12 -

Insert the upper flue into the lower flue. Fix the lower flue

to the hood using the screws B provided (Fig.4), extract

the upper flue up to the bracket and fix it with the screws

B (Fig.3). To transform the hood from a ducting version

into a filtering version, ask your dealer for the charcoal

filters and follow the installation instructions.

• FILTERING VERSION

Install the hood and the two flues as described in the

paragraph for installation of the hood in ducting version.

To assemble the filtering flue refer to the instructions

contained in the kit. If the kit is not provided, order it

from your dealer as accessory. The charcoal filters must

be fitted in the ducting unit located inside the hood

(Fig.7).

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to

cooking.

It is recommended to leave the appliance in operation for

15 minutes after cooking is terminated in order to com-

pletely eliminate cooking vapours and odours.

The proper function of the cooker hood is conditioned by

the regularity of the maintenance operations, in particu-

lar, the active carbon filter.

• The anti-grease filters capture the grease particles

suspended in the air, and are therefore subject to clog-

ging according to the frequency of the use of the appli-

ance.

In order to prevent fire hazard, it is recommendable to

clean the filter at a maximum of 2 months by carrying out

the following instructions:

- Remove the filters from the cooker hood and wash them

in a solution of water and neutral liquid detergent, leaving

to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several

washes. This is not cause for customer complaint nor

replacement of panels.

• The active carbon filters purify the air that is replaced

in the environment. The filters are not washable nor re-

useable and must be replaced at maximum every four

months. The saturation of the active carbon filter de-

pends on the frequency of use of the appliance, by the

type of cooking and the regularity of cleaning the anti-

grease filters.

• Clean the fan and other surfaces of the cooker hood

regularly using a cloth moistened with denatured alcohol

or non abrasive liquid detergent.

• The illumination installation is designed for use during

cooking and not for prolonged general illumination of the

environment. Prolonged use of the illumination installa-

tion notably reduces the duration of the bulb.

COMMANDS: (Fig.5)

Push-button A = on/off lights switch

Push-button B = on/off cooker hood switch. The appli-

ance switches on at speed level 1, If the cooker hood is

on depress the push-button for 2 sec. to switch off the

cooker hood. If the cooker hood is at speed level 1 it will

not be necessary to depress the push-button to switch

the cooker hood off. Decreases the motor speed.

Display C = indicates the motor speed level selected

and activates the timer.

Push-button D = switches on the cooker hood. Increases

the motor speed. Touching the key at 3rd speed, the

intensive function runs for 10', then the appliance go

back to work at the original speed. During this function

the display blinks.

Key E = The Timer times the functions on activation for

15 minutes, after which they are switched off. The Timer

is deactivated by re-pressing Key E. When the Timer is

activated the decimal point must flash on the display.

The Timer cannot be activated if the intensive speed is

functioning.

The “clean air” function is activated by pressing key E

for 2 seconds when the appliance is switched off. This

switches the motor on for 10 minutes every hour at the

first speed. During functioning a rotary movement of the

peripheral segments must be visualised on the display.

When this time has passed the motor switches off and

the fixed letter “C” must be visualised on the display

until the motor re-starts after 50 minutes for another 10

minutes and so on. Press any key apart from the light

keys to return to normal functioning. Press key E to

deactivate the function.

• Active carbon/grease filter saturation:Fig.5

- When display item C flashes, at a speed where it

alternates with the letter F (e.g. 1 and F), the grease

filters must be washed.

- When display item C

flashes, at a speed where it

alternates with the letter A (e.g. 1 and A), the carbon

filters must be replaced.

After the clean filter has been positioned correctly

, the

electronic memory must be reset by pressing button A

for approximately 5 seconds, until the indication F or A

shown on the display C stops flashing.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR EVENTUAL DAMAGES CAUSED BY BREACHING

THE ABOVE WARNINGS.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ATAG ws9011em in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATAG ws9011em

ATAG ws9011em User Manual - English, German, Dutch, French - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ATAG ws9011em Manual

Product: