109644

ATAG WS 9011 FM Manual

12
Zoom out
Zoom in
Previous page
1/13
Next page
- 13 -
GENERAL
Carefully read the following important information regarding
installation safety and maintenance. Keep this information
booklet accessible for further consultations.
The appliance has been designed for use in the ducting
version (air exhaust to the outside – Fig.1B), filtering
version (air circulation on the inside – Fig.1A).
SAFETY PRECAUTION
1. Take care when the cooker hood is operating simulta-
neously with an open fireplace or burner that depend on
the air in the environment and are supplied by other than
electrical energy, as the cooker hood removes the air
from the environment which a burner or fireplace need for
combustion. The negative pressure in the environment
must not exceed 4Pa (4x10-5 bar). Provide adequate
ventilation in the environment for a safe operation of the
cooker hood. Follow the local laws applicable for external
air evacuation.
Before connecting the model to the electricity net-
work:
- Control the data plate (positioned inside the appliance)
to ascertain that the voltage and power correspond to
the network and the socket is suitable. If in doubt ask a
qualified electrician.
- If the power supply cable is damaged, it must be replaced
with another cable or a special assembly, which may be
obtained direct from the manufacturer or from the Technical
Assistance Centre.
2. WARNING !
In certain circumstances electrical appliances may
be a danger hazard.
A) Do not check the status of the filters while the
cooker hood is operating
B) Do not touch bulbs or adjacent areas, during or
straight after prolonged use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker
hood
D) Avoid free flame, as it is damaging for the filters
and a fire hazard
E) Constantly check food frying to avoid that the over-
heated oil may become a fire hazard
F) Disconnect the electrical plug prior to any mainte-
nance.
G) This appliance is not intended for use by young
children or infirm persons without supervision
H) Young children should be supervised to ensure they
do not play with the appliance
I) There shall be adequate ventilation of the room
when the rangehood is used at the same time as appli-
ances burning gas or other fuels
L) There is a risk of fire if cleaning is not carried out
in accordance with the instructions
This appliance conforms to the European Directive EC/
2002/96, Waste Electrical and Electronic Equipment
(WEEE). By making sure that this appliance is disposed
of in a suitable manner, the user is helping to prevent
potential damage to the environment or to public health.
The
symbol on the product or on the accompanying
paperwork indicates that the appliance should not be
treated as domestic waste, but should be delivered to a
suitable electric and electronic appliance recycling
collection point. Follow local guidelines when disposing
of waste. For more information on the treatment, re-use
and recycling of this product, please contact your local
authority, domestic waste collection service or the shop
where the appliance was purchased.
INSTALLATION INSTRUCTIONS
Assembly and electrical connections must be carried
out by specialised personnel.
• Electric Connection
The appliance has been manufactured as a class II,
therefore no earth cable is necessary.
The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral
If not provided, connect a plug for the electrical load
indicated on the description label. Where a plug is pro-
vided, the cooker hood must be installed in order that the
plug is easily accessible.
An omnipolar switch with a minimum opening of 3mm
between contacts, in line with the electrical load and
local standards, must be placed between the appliance
and the network in the case of direct connection to the
electrical network.
• The distance between the surface supporting the
cooking containers on the cooking device and the bottom
of the kitchen hood must be a minimum of 65 cm (if it is
a gas hob) and 45 cm (if it is an electric or induction
heating system hob).
If a connection tube composed of two parts is used, the
upper part must be placed outside the lower part. Do not
connect the cooker hood exhaust to the same conductor
used to circulate hot air or for evacuating fumes from
other appliances generated by other than an electrical
source.
• In the case of assembly of the appliance in the suction
version prepare the hole for evacuation of the air.
• Before starting to fix the hood, disconnect the anti-
grease filter B (Fig.6) for easier appliance handling.
Before this operation, perform the following steps
depending on the model purchased:
MODEL 1
Remove the 3 panels A as shown in Fig.4.
Pull handle B as shown in Fig.6.
MODEL 2
Open panel C as shown in Fig.5.
Pull handle B as shown in Fig.6.
If the appliance has a lid, remove it by removing the 4
screws B as shown in Fig.9A.
• WALL FIXING
Mark the position of the lower side of the hood on the wall
(Fig.2A). Maintain the minimum distance required from
the hob as shown in Fig.2B.
- Position the fixing template on the wall, making sure
that the line coincides with the line previously made on
the wall.
- Mark the fixing holes and cut them into the material
(Fig.3).
- Fix the 2 top screws K and screw anchors (Fig.3),
without tightening them completely.
- Place the appliance against the wall, align it in horizontal
position and tighten screws K (Fig.7).
- Once the adjustment has been completed, fix the hood
using the 2 screws C (Fig.8).
- When carrying out the fixing operations, use only screws
and screw anchors suited to the type of wall (e.g.
reinforced concrete, plasterboard etc.).
- If the screws and screw anchors are supplied with the
appliance, make sure that they are suited to the type of
wall to which the hood must be fixed.
ENGLISH
GB
… 12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG WS 9011 FM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG WS 9011 FM in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info