108867
24
Zoom out
Zoom in
Previous page
1/25
Next page
GB 9
maintenance
cleaning
The filters can also be cleaned by hand. Clean the filters in
soapy water made with washing-up liquid and rinse them.
Allow the filters to drain well (through the slits at the side).
The underside of the extractor hood can be cleaned with a
mild cleaning agent and a damp cloth. Dry with kitchen paper
or a dry cloth.
replacing
The filters can only be put back in place in one way. Be
careful about the correct position of the filters. The covered
part of the filter should be at the back. In the case of the left-
hand filter this part is at the back on the right. The centre
filter (where applicable) is covered at the back over its entire
width. In the case of the right-hand filter the covered part is
at the back on the left. NB: the island hood has 4 identical
filters.
1 Push the rear of the filter into the holder.
2 Push the front upwards until it will not go any further.
3 Let the filter slide forwards.
The filter is again in its correct position.
4 Erase the memory of the grease filter indicator (see
page 7, "operation – grease filter indication").
replacing the carbon filter
Replace the carbon filter twice a year. This only applies to
recirculation hoods.
Put the carbon filter in the space intended for it above the
filters.
90 cm wide:
Be careful about the
correct position of
the filters.
GB 8
maintenance
cleaning
duct and hood
For cleaning the stainless steel parts and the glass plate, you
can best use a mild cleaning agent (washing-up liquid) and a
damp cloth. Dry with kitchen paper or a dry cloth.
The stainless steel regains its shine if you occasionally use a
stainless-steel care product or polish. The polish applies a
dirt-resistant layer to the stainless steel. Always clean the
stainless steel in the direction of polishing.
Atag supplies cleaning and care products for extractor hoods.
Never use abrasive cleaning agents (such as Vim, green
scourers or other scouring pads) or polishing cleaning agents
(such as liquid abrasives). Never use caustic agents. These
can attack the stainless steel.
grease filters
Clean the grease filters as soon as the grease filter indicator
lights up (see also page 7, "grease filter indicator").
removing
1 Switch the fan and lighting off.
2 Push the filter backwards using the indentation and pull
the front downwards.
3 Remove the filter from the hood.
cleaning
You can clean the filters in the dishwasher. Let the filters
drain well (through the slits at the side) before putting them
back.
removing grease
filters
120 cm wide:
Be careful about the
correct position of
the filters.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG WS 1011 ZM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG WS 1011 ZM in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info