121818

ATAG WCA.2 Manual

36
Zoom out
Zoom in
Previous page
1/37
Next page
GB 15
assembly
buiding in
GB 14
installation
general
clearance required
The distance between the underside of the extractor hood
and the hob should be at least 65 cm. For gas hobs, this
distance should be a minimum of 70 cm.
fitting possibilities
You can use the extractor hood for recirculation or for
extraction. An extractor hood blows the fumes through the
discharge to the outside.
In the case of a recirculation hood, a carbon filter removes
the fumes. The clean air is blown back into the kitchen.
For instructions on installing the carbon filter see "setting" on
page 10.
650/700
against the wall
1 Remove the filters from the extractor hood.
2 Hold the hood against the wall.
3 Working through the hood or using a fitting template,
draw the mounting holes (A) and the hole to secure the
hood (B).
4 Drill the holes.
5 Push the wall plugs supplied into the holes.
6 Insert the screws into the 2 mounting holes (A).
NB: screw the screws in until 1 cm is left protruding from
the wall.
7 Fit the flue ring (E) to the extractor hood. Tighten the
screw (F) with which the flue ring is secured.
8 Hang the hood on the 2 mounting screws.
9 Tighten the mounting screws.
10 Tighten the locking screw.
11 Connect the flue pipe to the flue ring.
below a kitchen cupboard
1 Working through the hood or using a fitting template,
draw the 4 mounting holes (A), the hole for the power
lead (C) and the hole for the flue (D) on the bottom of the
kitchen cupboard.
2 Drill the holes.
3 Fit the flue ring (E) to the extractor hood. Tighten the
screw (F) used to secure the flue ring.
4 Pull the power lead upwards through the hole provided
and push the flue ring through the opening.
5 Hang the hood, through the bottom of the kitchen
cupboard, on the 4 mounting screws. Tighten the screws.
6 Connect the flue pipe to the flue ring.
A
A
B
C
A
A
A
A
D
E
F
E
F
… 36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG WCA.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG WCA.2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info