481548
37
Zoom out
Zoom in
Previous page
1/42
Next page
71
FAULTS
If the appliance does not work properly, it does not always mean that it is
defective. Try to deal with the problem yourself first. Phone the service
department if the advice given below does not help. Only authorised
personnel may carry out work on the gas and electrical part.
table
fault
There is a smell of gas in the
vicinity of the appliance.
A burner does not ignite.
The burner does not burn evenly.
The burner goes out after igniting.
cause
– A burner is turned on but not lit.
The coupling on a bottled gas
unit has come undone.
– Burner parts not correctly
installed.
– Fuse defective/fuse in meter
cabinet switched off.
– Plug not in socket.
– Sparkplug dirty/damp.
– Burner parts dirty/damp.
– Ventilation opening at the rear
closed.
– Main gas tap closed.
– Fault in the gas network.
– Gas bottle or tank is empty.
– Control knob not kept pressed
in long enough or far enough
(HG61/76/91/96).
– Control knob turned too quickly
through ignition position
(HG41).
– Burner parts incorrectly installed.
– Burner parts dirty or damp.
– Wrong type of gas used (where
bottled gas is used).
– Control knob not kept pressed
in long enough
(H61..B/HG76..B/
HG91..B/HG96..B).
solution
– Close the tap and wait for a few
minutes before relighting.
Tighten the coupling.
– Assemble the burner parts using
the centring ridges.
– Fit a new fuse or switch the
automatic fuse back on.
– Push the plug into the socket.
– Clean and dry the sparkplug.
– Clean and dry the burner parts,
making sure that the outflow
holes are open.
– Ensure adequate air supply.
– Open the main gas tap.
– Check with your gas supplier.
– Connect a new gas bottle or
have the tank filled.
– Keep the control knob pressed
in far enough between full and
low for at least 5 seconds.
– Light the burner in the ignition
zone.
– Assemble the burner parts using
the centring ridges.
– Clean and dry the burner parts,
checking that the outflow holes
are open.
– Check that the gas used is
suitable for the appliance.
– Keep the control knob pressed
in for at least 5 seconds.
70
MAINTENANCE
stubborn stains on stainless steel (spillage wells)
In particular boiled over red cabbage, red beetroot, soysauce, rhubarb and
other foodstuffs with a high sugar content and acidic liquids can cause
discoloration of the surface.
If you want to remove stubborn stains from stainless steel, you can best
use a cleaning agent specially formulated for stainless steel. In that case,
always clean in the direction of the structure of the steel in order to avoid
shiny spots. (Damage resulting from this are not covered by the
warranty!)
If the stains cannot be removed using the method described above, you
can clean the hob with HG oven and grill cleaner. Bear in mind,
however, that you will have to clean the whole of the spillage well in
order to avoid differences in 'colour'. You must also treat the spillage well
afterwards with a polish or maintenance product for stainless steel. It is
normal for the surface to discolour somewhat during the product's
lifetime.
Keradur
®
burner bases
The burner bases have a unique Keradur
®
surface coating. The special
dirt-repelling lacquer has a ceramic filling which makes cleaning easier
and substantially improves the durability of the burners. The burner
bases are best cleaned with a mild cleaning product and a soft cloth.
general
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG HG6153A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG HG6153A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info