691098
1
Zoom out
Zoom in
Previous page
1/2
Next page
ASSEMBLY
Introduction
The Assault Fitness AirRunner treadmill requires only minor assembly. All tools required to complete the initial
setup and assembly have been included in the Assembly Hardware Kit.
Remove the unit and all parts from the carton and packaging. Conrm all parts shown in the section titles As
Shipped are included before attempting assembly of the AirRunner.
Assembly Step One: Upright Installation
Locate the Speed Sensor Cable – Lower (549a) and ensure the end/connector is extending from the main
frame.
Raise the Upright – Left vertically, ensuring the Keyholes are located at the bottom. Align the Upright - Left
keyholes with the two posts located on the main frame. This will support the upright while completing the
installation.
Connect the Speed Sensor – Lower (549a) and Speed Sensor Cable – Middle (560b) connectors rmly.
Locate three (3) sets of #534 Hex Screws and #562 Flat Washers, and loosely thread each assembly through the
Left Upright and into the main frame. Tighten the screws rmly.
Hang the Upright – Right keyholes onto the Main Frame posts and install the remaining three (3) sets of #534
Hex Screws and #562 Flat Washers.
6
Console (514)
Console Cover
- Right Inner (530)
Console Cover
- Right Outer (531)
Upright - Left
(502)
Upright
- Right (503)
Sidecase Center Cover
- Right (510)
Sidecase Center Cover
- Left (507)
Main Assembly (A)
Console Cover
- Left Inner (529)
Console Cover
- Left Outer
(528)
Handrail (504)
Speed Sensor Cable - Upper (559a)
Speed Sensor
Cable
- Middle (560a)
Speed Sensor
Cable - Middle
(560b)
Speed Sensor
Cable - Upper (559b)
Speed Sensor
Cable - Lower (560a)
Console Cable
(514a)
ASSEMBLY TOOLS
AA Alkaine
Batteries
4 pieces
4mm
Hex Wrench
5mm
Hex Wrench
13/16mm
Open-Ended
Wrench
Button Head Hex Screw M8 x 20mm (535)
Hex Screw M10 x 75mm (534)
HARDWARE DESCRIPTION DRAWING QUANTITY
Flat Washer Ø20OD x 11ID x 1.5t (562)
Phillips Head Screw M4.2 x 13mm (538)
6
6
12
AS SHIPPED
MANUAL TREADMILL
QUICK START
GUIDE
534
562
560b
560(a)
562
534
549a
Upright - Left
Upright - Right
Keyholes
Posts
507
537537
537
510
537
Upright
Assembly Step Two: Sidecase Covers
Locate the Sidecase Center Cover - Left (507). Align the tabs locate at the top with the receivers on the installed
sidecase plastics. To install, the cover will hinge downward and snap in place. Ensure the outer surface of the cover
is ush or aligned with the adjacent plastics.
Secure with two (2) #537 Phillips Head Screws.
Remove the four (4) #564 Hex Screws
from the backside of the Console (514)
and set them aside.
Connect the Console Cable (514a) and
Speed Sensor Cable – Upper (559b)
connectors and carefully tuck the excess
cable into the Handrail.
Loosely thread the four (4) #564 Hex
Screws through the mounting plate on
the Handrail and into the backside of the
Console (514). When all four (4) screws
are installed, tighten rmly.
With the help of a second person, support
the Handrail assembly above the uprights
and connect the Speed Sensor Cable –
Upper (559b) and Speed Sensor Cable –
Middle (560a) connectors. Carefully tuck
the connectors and excess cables into the
left Upright.
Set the left and right Handrail brackets
inside the left and right Uprights. While
supporting the Handrail Assembly,
loosely thread three (3) #535 Button
Head Hex Screws through the left
Upright and into the Handrail bracket.
Assembly Step Four – Final Adjustments
Identify a suitable location that is level and oers enough space for the unit with the minimum required free
space. It is recommended that the AirRunner be sited with a minimum of 0.5 meters (19.7 in.) of clearance from
the nearest walls or other equipment to the left, right and front of the unit. A minimum of 2.0m (79”) of clearance
should be maintained to the rear of the AirRunner.
CAUTION: THIS TREADMILL IS HEAVY. INJURY CAN OCCUR IF PROPER LIFTING TECHNIQUES
ARE NOT PRACTICED.
To relocate, raise the rear of the unit with by grasping the transport handle and slowly rolling the AirRunner to
the desired location.
Ensure the unit is level and does not rock by adjusting the Stabilizer Leveling Feet. Two feet are located at the rear
of the main frame. As a starting point, loosen each foot by threading the assembly downward/clockwise, and
then thread the locknuts downward (clockwise) against the base of the foot. Check the unit for stability and make
any adjustments as necessary. Once stable, lock the Stabilizer Leveling Feet in place by tightening the jamb nut
upward/counter-clockwise, against the underside of the frame to lock the current positions for each foot.
Congratulations. The assembly of your Assault Fitness AirRunner treadmill is complete. Please read all included
information, user guides and warnings before use.
Assembly Step Three – Handrail & Console Installation
Repeat this step for the right side and tighten all six (6) screws rmly.
Align the Console Cover – Left Outer (528) with the outside of left Handrail bracket, and thread two (2) #537
Phillips Head Screws through the handrail bracket and into the #528 Cover. Repeat this step for the right side
with Console Cover – Right Outer (531).
Align the Console Cover – Left Inner (529) with the inside of the left Handrail bracket install two (2) #537
Phillips Head Screws through the #529 Cover and into the #528 Cover.
Align the Console Cover – Right Inner (530) with the inside of the right Handrail bracket and install two (2)
#537 Phillips Head Screws through the #530 Cover and into the #531 Cover.
5803 Newton Drive Carlsbad, California 92008 Ph. 1.888.815.5559
For more information or questions regarding your equipment, please visit our website at
AssaultFitnessProducts.com
© Assault Fitness 2017
514a
514
Handrail (504)
535
535
535
535
535
535
Upright
528
560a
559b
537529 530
531
537
564
504 559b
Stabilizer
Leveling
Foot
Part #23-AS-566 US-English v1.0 05-Mar-17
1


Need help? Post your question in this forum.

Forumrules
1

Forum

assault-airrunner

Reset search

  • My monitor pauses after 5 seconds and doesn’t display the speed. Have changed batteries etc is there a reset button (as opposed to just holding down stop bottom). Submitted on 25-1-2022 at 20:59

    Reply Report abuse
    • I’m having this same issue. Have you figured out the issue with yours? Answered on 8-3-2022 at 22:37

      Vote up (5) Report abuse
    • I kept changing the batteries, but I think it’s down to the cold weather. Mine is stored in my garage so it gets really cold in there. I wrap it up most nights which helps a little Answered on 9-3-2022 at 14:06

      Vote up Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Assault AirRunner at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Assault AirRunner in the language / languages: English as an attachment in your email.

The manual is 3,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Assault AirRunner

Assault AirRunner User Manual - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info