315289

Asko wt 6332 w Manual

50
Zoom out
Zoom in
Previous page
1/52
Next page
- 50 -
6 / INCIDENTS AND PARTICULAR MESSAGES SHOWN ON THE DISPLAY
•INCIDENTS THAT MAY OCCUR
•The cycle does not start
— You have not pressed the "Start/Pause" button
— There is no power to the machine:
- Check that the plug is correctly in the socket
- Check the circuit breaker and the fuses.
— The water tap is closed
— The machine's lid is not closed properly
•A puddle of water forms around the machine
Warning:
First of all remove the plug and the fuse and shut off the water
supply tap.
While the machine is operating, the permanent level control prevents
the water from overflowing. If, despite this, water comes out of your
machine, it may be that:
— The drain hook is wrongly positioned in the drain pipe.
— The water supply hose is not sealed tightly at the machine or tap end:
- Check that the seals are in place and the connections are tight.
•Heavy vibration during spin
— All the transport materials have not been removed correctly from
the machine:
- Check that all the transport wedges have been removed (see
"REMOVING THE TRANSPORT CLAMPS").
— The floor is not level.
— Your machine is resting on its two “front” castors (depending on the
model):
- Reset your machine on its feet by pushing the castor engagement
lever to the right.
•The washing is not spun or not spun enough
— You have selected a programme with no spin, for example "Drip-dry"
— The spin safety system has detected poor distribution of the washing
in the drum:
- Untangle the washing and programme a new spin.
• The machine does not drain
— You have programmed "Full drum stop"
— The pump filter is blocked:
- Clean it (see "CLEANING THE PUMP FILTER" for the relevant
procedure)
— The drain hose is kinked or squashed
• The lid does not open
— The programme has not yet finished
The lid remains locked throughout the programme.
• The drum doors open very slowly
(On machines fitted with gently opening doors)
— Your machine has not operated for a long time
— It is located in too cold a position.
— Detergent residue (powder) is blocking the hinges
- In all cases, everything returns to normal after the doors have opened
initially
Important :
As a general rule, whatever the anomaly detected, you
should stop the machine, unplug the power cable and shut off the
water tap
• AFTER-SALES SERVICE :
Possible maintenance on your washing machine should be undertaken
by :
— either your dealer,
— or another qualified mechanic who is an authorized agent for the
brand appliances.
When making an appointment, state the complete reference of your
equipment (model, type and serial number). This information appears
on the manufacturer's nameplate attached to the rear of the equipment.
•MESSAGES SHOWN ON THE DISPLAY
•Incidents indicated, which you can rectify yourself
In this section, we explain how you can rectify these incidents
very easily yourself.
Your machine automatically detects some operating incidents and
indicates these by particular messages shown on the screen.
Messages Causes / Remedies
Drum blocked. Check that a small item of laundry (e.g.
a handkerchief or a sock, etc.) has not slipped down
between the tub and the drum and is stopping the drum
from turning. To access the bottom of the tub, please
refer to the section
“
CLEANING THE PUMP FILTER
”.
The pump filter is clogged. Clean the pump filter (for
how to do this, see the section “CLEANING THE PUMP
FILTER”) and then press the “Start/Pause” button
again to restart the cycle.
Also check the drain hose’s position in the drain: the
connection must not be airtight (see the section
“DRAINING AWAY THE WASTE WATER”).
Drain hose not positioned properly. Check the drain
hose’s position in the drain: the connection must not
be airtight (see the section “DRAINING AWAY THE
WASTE WATER”).
The water tap is closed. Check that the water tap is
open and then press the “Start/Pause” button again to
restart the cycle. This incident may also be caused by
the drain hose being poorly connected (see the
section “DRAINING AWAY THE WASTE WATER”).
Lid not closed properly. Check that the lid is closed
and then press the “Start/Pause” button again to
restart the cycle.
EN
•Duration of program is shorter or longer
This condition is normal and is not an error or failure. The duration
of the program, displayed at the beginning of the program, adjusts
individually to the weight and amount of load (automatic weighing).
It guarantees optimal wash efficiency and water and energy
consumption, which are adjusted to the quantity of laundry. The
system of safe spinning and lather removal can extend the duration
•
Functional remarks – the below cases are not
considered as failure:
of the program displayed at the beginning.
• Incidents indicated that require a breakdown engineer
Important:
Check that the message displayed is not for an incident you can
repair yourself.
Your machine also detects some operating faults that systematically
require the services of a breakdown engineer and informs you of this
through other messages of we provide some examples below.
When one of these messages is shown, remember to note it down so
that you can pass it on to your breakdown engineer when you call him
to assist him in his task.
NB:
Before calling your breakdown engineer, we recommend that you do
the following:
-
Set the Programme selector to the “0” position and remove the
electrical plug for at least 10 seconds
-
Reconnect the plug and restart a washing cycle.
If the fault persists, call your breakdown engineer and remember to tell
him which message is displayed.
Important:
Do not restart a washing cycle if the drum remains locked or if
you notice water around your machine of if you notice a burning smell.
etc...
Messages
… 50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Asko wt 6332 w at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Asko wt 6332 w in the language / languages: English, Dutch as an attachment in your email.

The manual is 7,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info