592662

Asics AP01-WJ32 Manual

32
Zoom out
Zoom in
Previous page
1/33
Next page
31
Troubleshooting Guide
Instr uc tion Ma nua l
AP01 : WJ32
For watch functions in general For running measurement functions
Problem Cause Remedy
Refer to
The di splay has be-
come blank.
The battery has run down.
Request the retailer from whom
the watch was purchased to re-
place the battery with a new
one immediately.

The watch gains or los-
es time temporarily.
The watch was left in a cold or hot
place.
The accuracy will be recovered
when the watch returns to the
normal temperature. Set the cor-
rect time before use.
P.9
The blur on the glass per-
sists.
Water got inside the watch due to dete-
rioration of the gasket or other reasons.
Consult the retailer from whom
the watch was purchased.

The timer does not re-
peat countdown.
The number of repetitions is set to 1
in the TIMER SETTING mode.
Set the number of repetitions
as desired in the TIMER SET-
TING mode.
P.11
The alarm will not ring
at the designated time.
The time zone set
for the TIME mode
differs from that set in the ALARM SET-
TING mode.
Activate the ALARM SETTING
mode to check if the time zone
is set correctly.
P.12
The alarm is not engaged for the alarm
channel for which the alarm time is set.
Select that alarm channel in the
ALARM mode, and activate the
ALARM SETTING mode to en-
gage the alarm.
P.12
The battery may near its end.
Check the battery life indicator.
If i
t indicates that the battery
nears its end, request the retailer
from whom the watch was pur-
chased to replace the battery
with a new one immediately.
P.8
The warning and time-
u p b e e p s w i l l n o t
sound.
The battery may near its end.
Check the battery life indicator.
If it indicates that the battery
nears its end, request the retailer
from whom the watch was pur-
chased to replace the battery
with a new
one immediately.
P.8
The backlight will not
light up.
Problem Cause Remedy
Refer to
- - - spm is shown for
th e SPM value for a
short time after the run-
ning is started.
It takes approximately 10 seconds af-
ter the running is started for the built-
in sensor to recognize that the move-
ment it senses is that of running.
The watch is intact, and can be
used as usual. If the SPM value
will not be shown after 10 sec-
onds, the watch may be out of or-
der. In t
hat case, consult a nearby
ASICS service facility.

Though lap time mea-
surement was made,
neither SPM nor pace
is displayed.
This watch is so designed that, if the
lap time measured is less than 30
seconds, the average SPM or pace of
the lap is not displayed, as a signifi-
cant measurement error may be in-
volved.
Measure a lap time when more
than 30 seconds have elapsed
from the start.

The algorithm was cus-
tomized, but the dis-
tance run indicated on
the display differs from
that actually run.
The data measured when you ran at a
speed too faster or slower than usual
was input in the SET_UP mode.
Use the data measured when you
run at a usual speed to customize
the a lgor ith m i n the S ET_U P
mode.
P.19
The AVG_PACE data
cannot be set.
Data beyond the settable range of the
running data was input. For
example,
invalid distance was set, or inappro-
priate adjustment of the transferred
time was made.
Set the running data within the
ranges below:
SPM: 60 ~250 SPM
Pace: 100 ~ 1959/km or 1
37 ~ 3210/mile
P.21
The SLOW PACE and
FAST PACE data can-
not be input.
An SPM value which is the same as
the AVG_PACE data cannot be input
as the SLOW PACE or FAST PACE
data.
Input an SPM value different from
the A
VG_PACE data.
P.19
The SLOW PACE and
FAST PACE data was
lost.
If the AVG_PACE data is updated, the
SLOW PACE and FAST PACE data
will be reset to 0.
Input the SLOW PACE and FAST
PACE data again.
P.19
When used for walking,
the SPM indicated on
the display differs from
that actually counted.
This watch is intended to measure
the number of steps during running,
and the accuracy of the SPM mea-
surement dur
ing walking may vary
significantly from user to user.
Swing the arms as sufficiently as
possible while walking.

… 32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Asics AP01-WJ32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Asics AP01-WJ32 in the language / languages: English as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info